Hello, can't establish a connection from my cEdge router to the vSmart. Any reason?IR1101-sdwan-ib# sh sdwan control sumcontrol summary 0vbond_counts 1vmanage_counts 1vsmart_counts 0 IR1101-sdwan-ib#sh sdwan control connIR1101-sdwan-ib#sh sdwan contr...
Forum Posts
The traffic between the loopback 0 interfaces of R1 and R2 should traverse through R3; R3 should be configured such that it translate 132.10.10.1 to 171.1.1.1 and 132.11.11.1 to 173.2.2.2 You can do NATTING only R3 router. After completing the sol...
Hi GuysA quick question, we have some Cat 9K switches with Network advantage licences.Are there any limitations when it comes to running BGP on them?We want to just receive a default route and do some basic route maps tuning on them.We are currently ...
Hi,I'm building a packet tracer network (see attached image) and had a question on putting ACLs in place to control interVLAN access [noting HSRP is set up on both distribution switches for redundancy].VLAN 21 10.20.21.0/24VLAN 27 10.20.27.0/24VLAN 8...
Hi I've got a cEdge (C1111-4PLTEEA) running version 16.12.3 IOS-XE SDWAN. All controllers are running 19.2.2. I am using Cisco automated certificates on controllers and onbox certificate option for hardware. I am struglling to make this router talk ...
Resolved! BGP route padding on Cisco ASR
Hello, I have two ASR routers running BGP between two connections. I am new to this so please bear with me. Basically we are running BGP at our hub office and would like to pad routes to certain branch offices to connection A or B. Is it possible to ...
The role of all data-link protocols is to control the correct delivery of data over a physical link of a particular type. For example, the Ethernet data-link protocol uses a destination address, which is the MAC address, field to identify the c...
Hi team I wanted to ask a question about a design Currently tcustomer has a total of 50 locations, they use a hub and spoke type topology (They are equipment 4331 and 4321, the customer wants to use their equipment until 2028.) 25 with a layer 2 ...
When I create a toplogy like below I've created SVI vlan 21 and SVI vlan 11 on all switches all links are trunk except the access ports pointing to the PCs.When I ping from switch D1 or D2 to the PCs, how am I able to ping across multiple ports wit...
I have to stacking 2 C9300 switches but I have a problema, today I have a external routed connectition connected one in each switch. After the stacking the switches will be come only one, how I can configure the interface (same Network) after the Sta...
Hello, I have a Cisco ISR4331 that is being used to route traffic from my ISP to my firewalls. I am looking to use Gig0/0/1 and Gig0/0/2 for my firewall's WAN connections, and they are redundant firewalls. Would the best configuration for this be s...
I noticed when I configure isr4331 via gui it doesn't sent a message to console buffer, I should see this message:Apr 10 08:32:53.958: %SYS-5-CONFIG_I: Configured from http by admin on 192.168.100.1and cisco prime doesn't do backup config from device...
Hi Members,Our Client VPN users are conecting using this IP 94.201.95.252. But im not able to figure out where this IP is configured.Found the Below on the Router, DO YOU THINK THIS COMMAND making the conection working.ip nat inside source static 172...
Hello.INTENT: Implement a solution that, when a pre-configured vendor box fails inside the LAN, the adjacent device will identify this failure, and then will remove an EIGRP distributed static route to a public IP-address that recursively points to t...
Hi, I experience problems with RTP concurrent sessions on a C927.The problem is that druing calls one side becoms silent for 3-4 secounds and then he comes back.It can happen 2 or 3 times in a single converation.The cal doesnt fall so it is not a SIP...
