Hi,I have below error when I tried to upgrade software of our vEdge1000 using CLI from 20.3.3 to 20.6.3.What is causing this error and how can I fix it? Thank you, vedge# request software install /home/admin/viptela-20.6.3-mips64.tar.gzgzip: invalid ...
Forum Posts
Hey all,Lately I've been working on a modern, practical training series covering OSPF. I wanted to share the videos with this community. OSPF Framework & OSPF Packets: LSDB, LSA, Hello, DBD, LSR, LSU, LSAckOSPF Areas and OSPF Types of Routers - Pract...
Hi Is it possible to apply time-based SD-WAN policy(ex> data or app-aware policy)?For example, certain traffic takes a specific link applied by a data policy during 9am - 5pm.
Resolved! Snmp v3 on Cisco IOS XE Cupertino 17.8.x
Hello guys, I try to configure snmp v3 in ISR routers 4451 with Coupertino 17.8.01 but it can't authentication. I configure same commands in Amsterdam 17.3.5 BUT it works truly. Is it about Software bug ? SrDoSnmp: authentication failure, Unknown...
I have a router I want to use to connect my LAn to the internet. I intend to use it only for NATing since I have an L3 switch doing a chunk of the routing. After configuration, I am able to ping myself, the LAN and the ISP IP but I am not able to bro...
Was trying to connect to vManage GUI for about 1h but couldnt.note: ping requests are successful.request nms all status command result:Problem
Hi to all,I have a situation like on attached picture. Central router 891 is currently Mikrotik router and it should be migrated to Cisco router.Internal networks are defined by VLANs, and outside interface to ISP is physical Gi0. I have configured o...
Hi I am learning python. Anyone can share some website where there are a lot of python code for us to reference?Thank you in advance.
Hello everyone,So my question is, I have 4 vbonds in my network, and they resolve by a FQDN so when a vedge comes up it will resolve the FQDN to 4 ip address and now I have 4 vbond ip addresses,so it will reach out to first one now if my first vbond...
Can the same service be deployed on multiple vEdges? i.e. can I add this to multiple vEdges that can reach 1.1.1.1 as a next-hop vpn 10 service FW address 1.1.1.1 is there a limit ... i.e. can I add this to 4 differant vEdges
Hi all, Is there any way to increase the boot disk size for Cisco VManage? Maybe through vshell? I'm not able to perform an upgrade to 20.3.vmanage:~$ dfFilesystem 1K-blocks Used Available Use% Mounted on/dev/hda1 2695680 1070592 1625088 40% ...
I set up a 4 routers network, each with one computer, using Packet Tracer but I cannot seem to make the computers from different networks communicate with each other using Static IP. I reviewed everything but I can't find what the problem is.Before p...
Resolved! Help, Packet Tracer Assignment
Hello, i'm looking for help with this assignment: file:///Users/darabhaqnazar/Downloads/en_ITN_SkillsAssessment-Student_Exam_00%20%20oeve_uden%20point%20(1).pdfI have configured all the ipv4 addresses to the pcs, vlan, and router. I'm at page 8 where...
July 27th till Aigust 4th, 2020 Ask Me Anything This event allows you to learn about platform positioning, as well as best migration practices and tools for a successful and cost-effective transition from vEdge infrastructure to IOS XE SD-WAN. Cisc...
Hello, I'm evaluating the use of the new Cisco edge 8500L device instead of the ASR1001 series.I read that the system is able to run in software two different IOS processes, I imagine that the system has an linux hypervisor with different VM or som...
