Hello all, We have an older ISR 4331 that experienced the dreaded clock component degradation bug CSCvb44543, and now the box is dead and won't boot. It is a lab box so no real harm done, but we also discovered that no backup of the config was done...
Forum Posts
I have a 4451 that is not in production and need to get it connected to the smart license portal. Is it possible to use the mgmt interface to allow smart license registration to connect?
We are in the process of graduating to Cisco's SD-WAN(Viptela) but in the meantime we have Cisco IWAN. Currently our internet hub router (ISR4451) is exceeding the performance 2Gb license. All routers at the hub level are ISR4451. Is it okay to mix o...
Resolved! Why is this lab using a PPP multilink?
This is a QoS lab R4(config)#interface serial 1/1R4(config-if)#encapsulation pppR4(config-if)#ppp multilinkR4(config-if)#ppp multilink group 1R4(config-if)#bandwidth 64R4(config-if)#no shutdownR4(config)#interface serial 1/2R4(config-if)#encapsul...
Hello, people,It would be great if you could help me to identify how many connections my router can support.I need to know how many connections an ISR 4321K9 (with licensed boots) can support. The reason for this is that I have a PIX cisco firewall w...
After several months of using a vMX on Azure, we discovered that the client tracking has been done incorrectly all this time leading to misinterpretations of the client traffic; such as assigning to an IP address traffic done by a different IP, displ...
Hello. I'm doing DMZ-Link BW in IOS XR and IOS XE as my internet facing router in the lab. For IOS, the bandwidth is 1024kbps and for XR it is 256k. Configurations below (I removed all unnecessary configs) R1 (XE)interface Ethernet0/2bandwidth 1024ip...
Hi all. on a Nexus 7kI need to change the Administrative Distance of a specific prefix from OSPF so EIGRP table has it at the new AD.for reasons, we already change the AD of the incoming OSPF routes to 180 so its higher than EIGRP but i have 1 prefix...
Hi all, I'm doing a practice with packet tracer to configure a Dynamic NAT overload (or PAT). In this practice, I have to create a Dynamic NAT overload with the following information: IP public address 65.0.0.15 and the router_principal Gig0/0...
Resolved! RIP V2 advertisement
I'm configuring RIP v2 on Cisco IOS XE 16.x version , my Subnet is 10. 181.1.0 MASK 255.255.255.0I need to advertise out the exact subnet not the full class A I don't want to summarize the addressIs it possible using RIP v2 ? if then what ...
I have got a new TP Link router Archer C24, it transmits both 2.4gHz and 5gHz. The issue I'm facing that it's signals keep disappearing or disconnecting after every hour or 30 mins. And it reappears or reconnects the moment i enter the IP 192.168.0.1...
Resolved! block access in same vlan
Hello all,We have 3 vlansvlan 10 - 192.168.1.0/24vlan 30 - 192.168.2.0/24vlan 40 - 192.168.3.0/24there is one server in vlan 10, server1 (192.168.1.5) and it only needs to access server2(192.168.1.9) on https port but its access to other clients on s...
Hi, I am facing a strange problem, as shown below, CPE-HQ WAN IP cannot ping CPE-Branch's WAN IP,From 25.25.1.2 cannot ping 25.25.2.2, the routes (25.25.1.0 255.255.255.252 and 25.25.2.0 255.255.255.252) present in routing table in respective VRF; Bo...
After making changes in the PBR ,I have to reload the Router to make the PBR work correctly. I need the command that needs to be executed after the policy, route-map or prefix-list of a PBR configuration has changed. The command is something akin to...
I got this C899G-LTE-GA-K9 and want to configure it for SIM0 with MTN Nigeria.Please can anyone upload the manual for configurations. Thank you
