I made a little lab where the aim was to make a route-map to remove the host 192.168.2.2 from the routing table of R1 (see topology) The ACL used in the route-map is a permit statement for host 192.168.2.2. The confusion is no matter if I put a per...
Folks, I have Cisco ASA5585 Chassis with two SSP-60 module installed in slot-0 and slot-1 for HA solution. I have question related how does chassis behave when we have two SSP-60 module installed. Does it act like two individual module connected or ...
We have the following hardware in ASR 9006 (fans and PSU skipped): RP/0/RSP0/CPU0:asr#admin show platformNode Type State Config State-----------------------------------------------------------------------0/R...
Hi,How to change ECMP on vedge routers, by default is 4 ECMP i want to increase the up to 8.What is the cli command ? I configured vedges by templates.Note: This is for my test lab.
Currently we are setting up a closed network and have introduced the CSR-1000V. In order to ensure we have access to multiple VLANs we have gone with a HSRP setup. With this setup we have two switches running ESS-3300-NCP and they are working using...
I was once a noob but now i think i know somthing more than noob (LOL). I have gone through routing protocols, vlan, inter-vlan routing, DMvpn, Site-to-site VPN etc. Now what shoud i do next ??? please mentors i need your suggestions. I want to beco...
ISR4300 - Boost license transfer during RMA Hi everyone and happy new year, one question has come to my mind recently.Last month I have registered boost license into an ISR4321 using PAK and Smart licensing system (just had to connect the router to t...
Hey, Is there a way to add expiry to a user account on Cisco 800 Router Series?
Hi, I think this will be an easy one for most of you but i just want to make sure.I have a router in the field that has two links back to our main network. Both links have an ip vlan with ospf on them.One of them is having problems and causing packet...
Hello, So i am trying to config router RIP v2 with this subnet IP: 129.208.63.1 but when i do it with command "#network 129.208.63.1" In Routing -> RIP i can see just Network Address 129.208.0.0 (!) The same happens when I do 129.208.48.0 and so o...
Hi there, For our monitoring and automation research I'm newbie in this solution. I followed the cisco information for the configuration. However I think to achieve access the topolopgy is as next:- vrf with public access using a VLAN and Loopback. T...
Hello, dear users, have a little problem with my lab. The task is to create three networks using three switches 2960-24TT with next ip addresses:192.168.3.0/255.255.255.0 (/24);10.0.1.0/255.0.0.0 (/8);172.17.1.0/ 255.255.0.0 (16)192.168.4.0/255.255.2...
Hi, In our core router we have 20 VRFs and it also receives full bgp tables from two ISPs for the Internet.So far, we have provided Internet to only one VRF, but we are planning to make Internet available to all VRFs in the future.We do not have enou...
Hi,HSRP running on nexus 9k sh ip ospf neighbors There are multiple VLAN , out of 10 VLAN one VLAN shows EXCHANGE/DR and the other side EXSTART /BDR what could be the issue switch2 172.16.10.110 1 EXCHANGE/DR 20w0d 192.168.8.3 Vlan10...
Good afternoon.I have configured BGP with BFD on my cisco ISR4451.During a tshoot session I have checked the "show bfd neighbors detail" and i found the following output: router#sho bfd neighbors det*** output omitted ***Registered protocols: BGP CEF...
