A customer is asking the possibility to remove the SSDs in a router processor (A99-RP2-TR) before return it to Cisco, due to the data security concern. I checked the genealogy of the product with a SN in Cesium and found there was no children SN list...
Hello,I am doing a little lab with VLXAN EVPN. I have configured the SPINE switches as border nodes, and peered them over iBGP with a WAN Edge router that is on SD-WAN. With the SD-WAN VPNs the setup and BGP peering was very straight forward. My SPIN...
Hello, everyone. I'm labbing IS-IS Area authentication, here is my topology: P1 router isis net 49.0001.1111.1111.1111.00 is-type level-1 area-password CISCO PE2-XE - this one is purposely configured without a password router isis net 49.0001.22...
I am trying to understand the device behavior when detaching an edge device from a template or removing it from a configuration group.In these scenarios, does the device retain the last applied (saved) configuration?Additionally, what is the correct ...
Hello. I have a scenario here as per diagram. All the Route/Switch (R/S) is NXOS Router/Switch (R/S)Site A has multiple static routes to (R/S)Site B. Site B also has multiple static routes to site A and at the same time has ospf running and redistrib...
I have the following topology. All devices are C8000V running IOS-XE 17.14.01aI'm trying to install a dynamic path SR-Policy from R1 to R4, but for some reason it doesn't come up.R1#show segment-routing traffic-eng policy allName: DYNAMIC (Color: 20 ...
I applied the ACL to the external interface on my C8300 router and the internet access block. below is my acl i applied on the interface for in/out bound remark DIV 13deny ip any any option any-options log-inputdeny icmp any host 13.28.162.111 frag...
hello I have a question relating to Application Aware Routing (AAR) on the Cisco Catalyst SDWANAs I understand the setup -- > BFD monitors & calculates the SLA if a site is configured with two interfaces both with DIA -- can the software monitor & ca...
I have attached my config file of cli template and feature template. BFD session goes down after attaching created device template, But works fine after attaching cli template. Configurations after attaching Device template and configurations after a...
Hello everyone,On my company, we are trying to implement Cisco SD-WAN NAT DIA on Service VPN 6136 only for traffic flows from O365 applications, through the public-internet local TLOC. We have 2 more transports: LTE (a low-bandwidth Internet link) an...
Hi,I work for an ISP which, like many others and amongst other things, provides fixed/dedicated public IPs via 1to1 static NAT through a Cisco Firepower ASA FW.I've had a customer of ours reporting the following recently:"The issue: We are seeing TCP...
How DC Cedge Communicate with On-Prem Controller with their Service VPN as we have Dual MPLS Link which is directly termintaed to Cedge (NO WAN Edge)One way may be connect one more link to cedge to Core Switch in VPN0(Global VRF) add static route for...
Hi,Need some clarification. Have a lab cluster up and running with 1x vManage, 1x vBond and 1x vSmart. All signed by the vmanage as the CA. Cluster has all nodes healthy - but then comes the first vedge along. devicehelper.cisco.com works, profile re...
Hi,I was reading this example: https://www.cisco.com/c/en/us/support/docs/routers/sd-wan/216012-why-traffic-is-not-load-balanced-over-ec.html Is see in show sdwan output that it shows always the same IP, but different color of remote peer.Is this may...
Hello,I am using SD-WAN Manager 20.15.3.1. I have configured SSO to access it via GUI. Users belonging to different groups are associated with a proper role after successful logon. I would like to use scope mechanism now however I have no idea how t...
