hi,just a sanity check here.is it safe to issue 'ip ssh version 2'? will it "break" or lock me out of the router?all VTY lines only allows SSH.Router#show ip sshSSH Enabled - version 1.99
Forum Posts
Dear ColleaguesI have some issue as some application does not work or very slow (Like cisco anyconnect show message "failed to launch downloader"). scenario is like below. I have Cisco 3750 Floor Sw (Stack of 3 Switch), Have Two Eigrp Uplink to N7K-1...
Currently we have static based routing in our internal setup however on exiting we have MPLS router acting as HUB point and more than 200 spoke sites on which we are running EIGRP to get routers from there and redistribute static routes from HUB to s...
Hello, I just purchased the ISR 1100 series router and I am having difficultly logging into it b/c I don't have the default user/password. Can someone please provide me with the default user/password? Also, are there any config steps I need to compl...
Looking for advice. I am the only network guy in a small-medium sized business. Currently have OSPF running on all switches, including the access/edge switches. I have 3 core switches in a triangle design. Each of those feed the access switches in d...
Hello Cisco users, I added the following line to my ASA 5540 firewall: access-list outside_access_in extended deny ip host 65.197.196.0 any This is the LAST statement in my list of permitted IP/ports. Unfortunately, Peerblock v1.2 on our Windows 201...
Resolved! router configuration
Hi everybody, I have a Cisco and I need to sync this router with a PTP server in my network. Reading about this configuration, I found different configurations and profiles and I don't understand how setting it exactly. Neither I know if I need to c...
Good day, i am installing my network at home and have a SG350 for my IPTV.The line comes in to my Service Provider supplied router, then goed to the SG350. On my service providers router i have DHCP enabled.Should i disable it on my SG350, or how sho...
Hello Team,I am new to networking. I am trying to set up a home lab for my training. I have Three cisco router 2800, cisco ass 5505, Cisco Switch Catalyst 3650and two IP phones 7960. I am trying to hook all these stuff together and to use my modem.Ca...
Hi, I would like advice on how to group the onboard GigEthernet ports 0/0 and 0/1 with switch GigEthernet ports 0/1/0, 0/1/1, 0/1/2 and 0/1/3 on the add in EHWIC-4ESG card... (if possible). I've setup a Vlan for and put the switch ports in it and the...
Resolved! BGP - Error vrf
Hi Guys. Im do a lab bgp on EVE and it Im tryed config a vrf. But display the error below. What can be causing error? R7(config-router)#address-family ipv4 vrf BLUE% Invalid address family ipv4 unicastvrf(0x1) BLUE
Has anyone else tried to upgrade the ASR1000-ESP40 to 16.9(5r) rom-monitor? If so did it work? I am getting the following when trying to upgrade. upgrade rom-monitor filename bootflash:asr1000-rommon.169_5r_SPA.pkg F0Upgrade rom-monitor on Embedded-S...
PE-2 ip vrf CustA rd 1256:12 route-target export 1256:16 route-target import 1256:16 router ospf 12 vrf CustA redistribute bgp 65100 subnets network 192.168.12.0 0.0.0.15 area 0 router bgp 65100 bgp log-neighbor-changes no bgp default ipv4-u...
Hi, I am sure this will have a trivial answer but it's annoying me... I have a Cisco 1921 router and have been using an EHWIC-4ESG 4 port switch card. It has 4 gig ethernet ports. I have now removed the card and I get errors in the terminal regarding...
I am trying to apply PBR on vlan 1 and 2 to reroute traffic for the specified host. However, the following errors are seen in the log message. Can someone advise a way to apply pbr on the C9500 L3 switch? The idea here is to pass all the internet an...
