887, DMT Bits Per Bin not working on ADSL2+

Napsterbater · ‎02-19-2012

I used to have a 877w in the same place and same setup as my current 887, this time though the DMT Bits Per Bin just will not populate on ADSL2+ altough it did work when it sync ADSL1 (same line/DSLAM, just came up ADSL for some reason).

Any Ideas? Its not a huge issue im just wondering.

car1#show dsl interface atm0

ATM0

Alcatel 20190 chipset information

ATU-R (DS) ATU-C (US)

Modem Status: Showtime (DMTDSL_SHOWTIME)

DSL Mode: ITU G.992.5 (ADSL2+) Annex A

ITU STD NUM: 0x03 0x2

Chip Vendor ID: 'STMI' 'GSPN'

Chip Vendor Specific: 0x0000 0x0010

Chip Vendor Country: 0x0F 0xFF

Modem Vendor ID: 'CSCO' 'GSPN'

Modem Vendor Specific: 0x0000 0x1000

Modem Vendor Country: 0xB5 0xFF

Serial Number Near: FTX142980A 887-SEC- 15.1

Serial Number Far: Chip ID: C196 (3) capability-enabled

DFE BOM: DFE3.0 Annex A (1)

Capacity Used: 84% 95%

Noise Margin: 14.5 dB 21.5 dB

Output Power: 20.5 dBm 12.5 dBm

Attenuation: 23.5 dB 8.0 dB

FEC ES Errors: 0 0

ES Errors: 1 10

SES Errors: 0 1

LOSES Errors: 0 1

UES Errors: 27 0

Defect Status: None None

Last Fail Code: None

Watchdog Counter: 0xC7

Watchdog Resets: 0

Selftest Result: 0x00

Subfunction: 0x00

Interrupts: 8780 (0 spurious)

PHY Access Err: 0

Activations: 2

LED Status: ON

LED On Time: 100

LED Off Time: 100

Init FW: init_AMR-5.0.007.bin

Operation FW: AMR-E-0.0.026.bin

FW Source: external

FW Version: 0.0.26

DS Channel1 DS Channel0 US Channel1 US Channel0

Speed (kbps): 0 14975 0 766

DS User cells: 0 471793

US User & Idle cells: 0 2170534

Reed-Solomon EC: 0 0 0 0

CRC Errors: 0 16 0 16

Header Errors: 0 13 0 1005

Total BER: 0E-0 33280E-0

Leakage Average BER: 0E-0 33280E-0

ATU-R (DS) ATU-C (US)

Bitswap: enabled enabled

LOM Monitoring : Disabled

DMT Bits Per Bin

Not able to get complete DMT bin information.Retry "show dsl" after few seconds.

DSL: Training log buffer capability is not enabled

paolo bevilacqua · ‎02-19-2012

Try updating IOS.

Napsterbater · ‎02-21-2012

Currently running c880data-universalk9-mz.151-4.M3.bin, I guess I can try c880data-universalk9-mz.151-3.T3.bin..

EDIT:

Well c880data-universalk9-mz.151-3.T3.bin is loaded, and now I get this.

car1#show dsl interface atm0

ATM0

Alcatel 20190 chipset information

ATU-R (DS) ATU-C (US)

Modem Status: Showtime (DMTDSL_SHOWTIME)

DSL Mode: ITU G.992.5 (ADSL2+) Annex A

ITU STD NUM: 0x03 0x2

Chip Vendor ID: 'STMI' 'GSPN'

Chip Vendor Specific: 0x0000 0x0010

Chip Vendor Country: 0x0F 0xFF

Modem Vendor ID: 'CSCO' 'GSPN'

Modem Vendor Specific: 0x0000 0x1000

Modem Vendor Country: 0xB5 0xFF

Serial Number Near: FTX142980AR

Serial Number Far:

Modem VerChip ID: C196 (3) capability-enabled

DFE BOM: DFE3.0 Annex A (1)

Capacity Used: 87% 95%

Noise Margin: 13.5 dB 22.5 dB

Output Power: 20.0 dBm 12.5 dBm

Attenuation: 23.0 dB 8.0 dB

FEC ES Errors: 0 0

ES Errors: 1 0

SES Errors: 1 0

LOSES Errors: 1 0

UES Errors: 0 0

Defect Status: None None

Last Fail Code: None

Watchdog Counter: 0x78

Watchdog Resets: 0

Selftest Result: 0x00

Subfunction: 0x00

Interrupts: 4305 (0 spurious)

PHY Access Err: 0

Activations: 1

LED Status: ON

LED On Time: 100

LED Off Time: 100

Init FW: init_AMR-5.0.007.bin

Operation FW: AMR-E-0.0.026.bin

FW Source: external

FW Version: 0.0.26

DS Channel1 DS Channel0 US Channel1 US Channel0

Speed (kbps): 0 14975 0 766

DS User cells: 0 119277

US User & Idle cells: 0 1568751

Reed-Solomon EC: 0 0 0 0

CRC Errors: 0 52 0 2

Header Errors: 0 34 0 0

Total BER: 0E-0 26112E-0

Leakage Average BER: 0E-0 26112E-0

Interleave Delay: 0 41 0 50

ATU-R (DS) ATU-C (US)

Bitswap: enabled enabled

LOM Monitoring : Disabled

DMT Bits Per Bin

000: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 3 0

010: 0 0 3 0 0 0 3 0 0 0 3 0 0 0 3 0

020: 0 0 3 0 0 0 3 0 0 0 3 0 0 0 3 0

030: 0 0 2 0 0 0 7 0 0 0 0 0 0 0 0 0

040: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

050: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

060: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

070: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

080: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

090: 0 0 3 0 0 0 3 0 0 0 3 0 0 0 3 0

0A0: 0 0 3 0 0 0 3 0 0 0 3 0 0 0 3 0

0B0: 0 0 2 0 0 0 7 0 0 0 0 0 0 0 0 0

0C0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

0D0: 0 0 3 0 0 0 3 0 0 0 3 0 0 0 3 0

0E0: 0 0 3 0 0 0 3 0 0 0 3 0 0 0 3 0

0F0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

100: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

110: 0 0 3 0 0 0 3 0 0 0 3 0 0 0 3 0

120: 0 0 3 0 0 0 3 0 0 0 3 0 0 0 3 0

130: 0 0 2 0 0 0 7 0 0 0 0 0 0 0 0 0

140: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

150: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

160: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 3 0

170: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

180: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

190: 0 0 3 0 0 0 3 0 0 0 3 0 0 0 3 0

1A0: 0 0 3 0 0 0 3 0 0 0 3 0 0 0 3 0

1B0: 0 0 2 0 0 0 7 0 0 0 0 0 0 0 0 0

1C0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

1D0: 0 0 0 0 0 0 3 0 0 0 3 0 0 0 3 0

1E0: 0 0 3 0 0 0 3 0 0 0 3 0 0 0 3 0

1F0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

DSL: Training log buffer capability is not enabled

paolo bevilacqua · ‎02-21-2012

Very good, please remember to rate useful posts clicking on the stars below.

Napsterbater · ‎02-21-2012

Well sorta, Sure I got the DNT Bits per Bin back, but they are completly wrong, if the line was that bad I wouldn't get the sync im getting.

paolo bevilacqua · ‎02-21-2012

Sorry, I didn't even looked. The next step would be logging a TAC case for cosmetic defect.

Napsterbater · ‎02-21-2012

Turns out it is a knowen issues with no workaround on the current versions.