ATM Mode on 2600 router

[pavloviandog]

I am trying to configure a newly installed 1MFT t1 WIC card for ATM communication. The router is a 2651 version 12.2. I have issued the mode atm, framing esf and linecode b8zs. But mode atm is not shown in the show run command. Have I missed a step?

2651#show run
Building configuration...

Current configuration : 956 bytes
!
version 12.2

!
ip subnet-zero
ip wccp web-cache
!
!
!
!
controller T1 0/1
framing esf
linecode b8zs
!
!
--More--

Any advice would be greatly appreciated...

[Edison Ortiz]

It's the WIC card present when issuing 'show diag' or 'show inventory'?

Perhaps your IOS code does not support the module.

Please refer to the WIC documentation:

http://www.cisco.com/en/US/products/hw/routers/ps259/products_data_sheet09186a0080088753.html

Cisco 2600 Series, 3660

•AIM-ATM: 12.2(2)XA/12.2.4T

•AIM-VOICE-30: 12.2(2)XB/12.2.8T

•AIM-ATM-VOICE-30: 12.2(2)XB/12.2.8T

and Feature set:

Any Cisco IOS "Plus" or "SP Services" Feature Sets

[pavloviandog]

I have a sneaking suspicion I don't have a compatable router. I do not have the choice of using AIM. Below is the version, and the show diag shows the T1 controller (see below)

2651#show ver
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-I-M), Version 12.2(8)T5,  RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2002 by cisco Systems, Inc.
Compiled Fri 21-Jun-02 08:50 by ccai
Image text-base: 0x80008074, data-base: 0x80A2BD40

ROM: System Bootstrap, Version 12.2(7r) [cmong 7r], RELEASE SOFTWARE (fc1)

2651 uptime is 3 hours, 35 minutes
System returned to ROM by power-on
System image file is "flash:c2600-i-mz.122-8.T5.bin"

cisco 2651XM (MPC860P) processor (revision 0x100) with 60416K/5120K bytes of memory.
Processor board ID JAD06400FP7 (3829963429)
M860 processor: part number 5, mask 2
Bridging software.
X.25 software, Version 3.0.0.
Primary Rate ISDN software, Version 1.1.
2 FastEthernet/IEEE 802.3 interface(s)
1 Serial network interface(s)
1 Channelized T1/PRI port(s)
32K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102

2651#show diag
Slot 0:
        C2651XM 2FE Mainboard Port adapter, 4 ports
        Port adapter is analyzed
        Port adapter insertion time unknown
        EEPROM contents at hardware discovery:
        Hardware Revision        : 1.0
        PCB Serial Number        : JAD06400FP7 (3829963429)
        Part Number              : 73-7756-02
        RMA History              : 00
        RMA Number               : 0-0-0-0
        Board Revision           : A0
        Deviation Number         : 0-0
        EEPROM format version 4
        EEPROM contents (hex):
          0x00: 04 FF 40 03 6F 41 01 00 C1 18 4A 41 44 30 36 34
          0x10: 30 30 46 50 37 20 28 33 38 32 39 39 36 33 34 32
          0x20: 39 29 82 49 1E 4C 02 04 00 81 00 00 00 00 42 41
          0x30: 30 80 00 00 00 00 FF FF FF FF FF FF FF FF FF FF
          0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

        WIC Slot 0:
        FT1
        Hardware revision 1.3           Board revision E0
        Serial number     29034259      Part number    800-03279-04
        Test history      0x0           RMA number     00-00-00
        Connector type    Wan Module
        EEPROM format version 2
        EEPROM contents (hex):
          0x20: 02 11 01 03 01 BB 07 13 50 0C CF 04 00 00 00 00
          0x30: 70 00 00 00 02 09 30 01 FF FF FF FF FF FF FF FF

        WIC Slot 1:
        T1 (1 port) WAN daughter card
        Hardware revision 1.0           Board revision D0
        Serial number     30306616      Part number    800-03568-03
        Test history      0x0           RMA number     00-00-00
        Connector type    PCI
        EEPROM format version 1
        EEPROM contents (hex):
          0x20: 01 20 01 00 01 CE 71 38 50 0D F0 03 00 00 00 00
          0x30: 68 00 00 00 03 05 30 00 FF FF FF FF FF FF FF FF

Slot 1:
        Unknown (type 216) Port adapter
        Port adapter is disabled
        Port adapter insertion time unknown
        EEPROM contents at hardware discovery:
        Hardware Revision        : 1.0
        Top Assy. Part Number    : 800-04797-01
        Board Revision           : G0
        Deviation Number         : 0-0
        Fab Version              : 05
        PCB Serial Number        : JAE0713081D
        RMA Test History         : 00
        RMA Number               : 0-0-0-0
        RMA History              : 00
        EEPROM format version 4
        EEPROM contents (hex):
          0x00: 04 FF 40 00 D8 41 01 00 C0 46 03 20 00 12 BD 01
          0x10: 42 47 30 80 00 00 00 00 02 05 C1 8B 4A 41 45 30
          0x20: 37 31 33 30 38 31 44 03 00 81 00 00 00 00 04 00
          0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

[Edison Ortiz]

on a XM router it should be support per the documentation. What does 'show inventory' displays?

http://www.cisco.com/en/US/docs/ios/voice/command/reference/vr_m3.html#wp1370241

Can you physically view the part number?

Regards,

Edison

[pavloviandog]

I don't have show inventory, I have show interfaces, which shows 1 serial port and two FastEthernet ports, but not the T1.

The part number is listed as 800-03568-03 from the show diag command.

[Edison Ortiz · Accepted solution]

I did a quick search and it shows as '1-port RJ-48 multiflex trunk VWICT1'

It's not an ATM module so the mode you need to use is T1, not ATM.

http://www.cisco.com/en/US/prod/collateral/routers/ps274/product_data_sheet09186a0080091b9c_ps259_Products_Data_Sheet.html

[pavloviandog]

Well I guess that is why I was unable to set the mode to ATM. Thanks Edison.

[pavloviandog]

One last thing... it only allows ATM as the mode of choice but doesn't list the mode from the show run.

2651#config t
Enter configuration commands, one per line.  End with CNTL/Z.
2651(config)#controller t1 0/1

2651(config-controller)#mode ?
  atm  Configure ATM mode

2651(config-controller)#mode atm ?
 

2651(config-controller)#mode atm
2651(config-controller)#

2651# show run

!
!
!
!
controller T1 0/1
framing esf
linecode b8zs
!
!
--More--

[Edison Ortiz]

Yes, the CLI won't prevent you from having the choice but the configuration won't take as the card itself isn't an ATM.