Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Don't miss this Cisco Catalyst 8000 offer

 
Labels

Forum Posts

Finding accurate answers to your questions and issues is always gratifying, but what if these answers are shared globally across different languages? The Cisco Community team has been working on a proof of concept (PoC) to take Accepted Solutions in...

translator.png Asolution.png htlm-source.png insertcode(1).png
Kelli Glass by Community Manager
  • 10030 Views
  • 7 replies
  • 16 Helpful votes

Hello , I need help to Change DHCP IP addresses range on my Cisco C1111 router, DHCP IPs range already configured from IP 192.168.1.2 to  192.168.1.254  I want to change that range to > from IP 192.168.1.150 to  192.168.1.200 Could you help me. What ...

I am configuring OSPF and while running packet captures I see at times hello packets are sent via unicast also I could see a few LS update packets are sent to a multicast address(as destination), may I know under what condition this happens?Thanks in...

RobotAjay by Level 1
  • 180 Views
  • 2 replies
  • 0 Helpful votes

How can I aply something like PBR but for the traffic originated from the router interface itself in a multi-homed setup? See the diagram attached.I have 10.0.0.1/31 configured on TenGigE0/0/0/1. I would like ping replies to ping requests to that IP ...

als95 by Level 1
  • 726 Views
  • 19 replies
  • 0 Helpful votes

Resolved! MPLS-TE cisco

Helloi want to know in which case, we will configure MPLS-TE in device IOS XR or IOS XE in the backbone ?it is mandatory ? i wait a reply fom expert SPThanks

I currently have a cisco ASR1001-HX (1SR) with rommon version: 16.9(4r) and IOS XE 16.12.04 and I want to upgrade to IOS XE 17.9.4a, according to the documentation I see that first I have to upgrade the rommon version to 17.3(1r). It is not clear to ...

I have a problem with pppoe server ghosts sessions: C 172.16.1.116 is directly connected, Virtual-Access2.7 is directly connected, Virtual-Access2.6 is directly connected, Virtual-Access2.5 ...

dominiaz by Level 1
  • 296 Views
  • 4 replies
  • 1 Helpful votes

hi,we've got ASR1K with IOS-XE version 16.9.x and using non-Smart license.the chassis is running the default 2.5 Gbps throughput.just a few questions:1.is the show platform hardware qfp active datapath utilization summary command used to find the cur...

Hello Guys. I have few VRF in one site, I can't figure out why I can't get a VRF traffic to the internet through the VTI tunnel, site A to B I already tried with PBR and it doesn't work. Goal. From Site A I want VRF LAN 10.200.30.0/24 to be able to g...

josebash by Level 1
  • 370 Views
  • 7 replies
  • 0 Helpful votes

Hi, I have a cisco asr 1001-x stuck in rommon mode. I entered a wrong command in rommon (confreg 0x2120) and reset. The router has since been stuck and can't boot into rommon mode or enable mode. I keep getting strange symbols like Gcs7 ]#sd. I will ...

Yuro by Level 1
  • 284 Views
  • 2 replies
  • 0 Helpful votes

when we attached 500 Mbps internet link to router V1000 then we got to know that V1000 has bandwidth limit of 250 Mbps only .hence 500 Mbps internet link does not work.1.how to check bandwidth limit of router and switch ?is it mentioned in data sheet...

knaik99 by Level 1
  • 346 Views
  • 3 replies
  • 0 Helpful votes

Hello,I'd like help setting up a nat destination on a C1111-4PLTEEA, Version 16.09.08, basically what I'd like to do is nat anyone who contacts my public ip address on port 500 to the private address 192.168.178.101 on 500, the public ip is not fized...

angelosss by Level 1
  • 496 Views
  • 6 replies
  • 0 Helpful votes