Finding accurate answers to your questions and issues is always gratifying, but what if these answers are shared globally across different languages? The Cisco Community team has been working on a proof of concept (PoC) to take Accepted Solutions in...
We have a Cisco ASR1001-X and it can only pass 750 megs of traffic thru it on a 10 Gig circuit. I looked at licensing levels and they seem correct. Anyone have any ideas of what I can look at? Both Lan and Wan interfaces are 10 gig and Wan is using S...
hi,will be using GLC-LH-SMD SFP in one of our ASR router.just need an advice on which type of fiber patch cord to use.the telco will run a SM fiber in their rack which is in another room, all the way to our DC rack which the patch panel hand off is L...
Assume that there are three router type devices outside firewall, and one core switch router behind one layer firewalland I would like to hide the router hop of core switch router from traceroute how to modify TTL to less values at router at the most...
Hi Is there any way design ASR + OTV Redundancy by routing instead EMM and bfd script ?We have two router ASR and 2 ISP Link to redundancy.So we now using EMM + bfd for control failover OTV link (active/standby) When Link ISP A down EMM action shu...
I have Two ASR 1001 but failover for return path doesn't workWorks fine leaving from firewall to ISP Problem when ISP trying to find firewallHSRP active R1 but Internet goes down by BFDtracert says ISP to router 2 10.10.10.2 than die finding to firew...
Hello We have ASR 1006X With software image 17.9 How to verify that it will support IPSec configuration? Is it related the rouer image or the license? Please note that, currently we didn't have access to it to verify using command line
Hi There,i am struggling a bit with our BGP Configuration and hopefully someone can give me a hint to right direction.We have 3 Routers in iBGP each of them has a WAN Connection to external AS (eBGP).Currently all Traffic is routed to only 1 external...
Hi all,Last January 21st, one of my ASR1001 crashed/reloaded with the following error:Jan 21 22:29:43 10.10.10.248 11451: ASR1.EQNX-PA3: Jan 21 22:29:42.492: %IOSXE_OIR-6-OFFLINECARD: Card (fp) offline in slot F0Jan 21 22:29:57 10.10.10.248 11452: AS...
Hi guys,I try to configure IPv6 with EIGRP for my topology; for some reason, the EIGRP routing table isn't learning the IPv6 subnet from its neighbor When I run 'show ipv6 route interface t0/0/0' on the router side and 'show ipv6 route interface e1/1...
Can someone explain what this configuration is doing, at a high-level, I am just trying to understand what is going on here? The route-map statements 20, 30, and 40 really don't do anything, correct? CPE-1 Configurationrouter bgp 2152neighbor casc-d...
Hi, we have one lease line with bandwidth 500Mbps, the current max transmit is 70Mbps. we have configured traffic shaping on the outgoing interface, and set CIR to 500Mbps. After applied QoS, still see the packet drop. The router interface is 1Gbps.C...
Do I have to redist for the BGP to have Rib and there is no around itrouter ospf 100passive-interface GigabitEthernet1network 3.3.3.3 255.255.255.252network 10.1.2.0 0.0.0.255 area 0!router bgp 100bgp router-id 3.3.3.3bgp log-neighbor-changesnetwork ...
Hi trying to add this command to an asr1k but its not taking it: ip receive access-list xx The command is listed in the ISO XE best practises guide, if its not supported on this platform is there a better way to restrict management access to all self...
Hello Everyone, I want to create different NAT rules for the same source based on the destination. Assume that I have the private range 10.0.0.0/8 and I want to create two NAT rules as follows:if range 10.0.0.0/8 wants to reach ACL1 then use the publ...
Hi In ASR1002X in address family on neighbor IP addressany I donnot find next Hop self configuration for ibgp
