Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Don't miss this Cisco Catalyst 8000 offer

 
Labels

Forum Posts

Finding accurate answers to your questions and issues is always gratifying, but what if these answers are shared globally across different languages? The Cisco Community team has been working on a proof of concept (PoC) to take Accepted Solutions in...

translator.png Asolution.png htlm-source.png insertcode(1).png
Kelli Glass by Community Manager
  • 10013 Views
  • 7 replies
  • 16 Helpful votes

Need some help with 9300 Static Routing.   We have a stacked 9300 being used as a collasped core with all of our VLANS on it. Each VLAN has an SVI and IP routing is enabled.  We also have a gateway of last resort set of the firewall that is connected...

The 9407 and 3750 are direct connect.SSH access fails due to an algorithmic issue.Please advise. 9407# C9407#ssh -l admin 192.168.10.10 [Connection to 192.168.10.10 aborted: error status 0] C9407# Jan 18 10:39:49.478: %SSH-3-NO_MATCH: No matching kex...

HELLO , I've configured an L2VPN point-to-point xconnect between the interfaces G1/0/13 and G1/0/11 using the following configuration  l2vpn xconnect context testmember GigabitEthernet1/0/11member GigabitEthernet1/0/13 interface GigabitEthernet1/0/11...

halima_0-1703604005861.png
halima by Level 1
  • 1675 Views
  • 12 replies
  • 0 Helpful votes

Hi Team, I have a problem that I can't do ssh to these switches (mark red), but I can do ssh to these multilayer switches (mark green). Anyone have the same issue with me? The background is that all of these devices must be remote controlled from a ...

izhangghani_0-1703844845279.png

Hi everyone, I am trying to deny VLANs to each other and only be reaching server VLAN. My commands below is successful on packet tracer but failed during implementation. ip access-list ext DenyVlans_50permit ip 172.16.50.0 0.0.0.255 172.16.36.0 0.0.3...

bryg0d by Level 1
  • 761 Views
  • 16 replies
  • 1 Helpful votes

SIT Router (Active Router) SIT DMZ (Standby router) Configuration: SIT (Active)int g0/0/1.20standby 2 ip 10.16.0.254standby 2 priority 110standby 2 preemptstandby track s0/1/0int g0/0/1.10standby 1 ip 10.17.0.254standby 1 priority 110standby 1 preemp...

212935n_2-1702824975383.png
212935n by Level 1
  • 470 Views
  • 8 replies
  • 0 Helpful votes

Hi guys, I have a confusion about eBgp multi-hop, i always see just the multihop sets to 2, when using loopbacks and we have a router between peers, but what if we have a couple of routers that we can't count what we'll set as mutli-hop, is still 2 h...

Kaneki007 by Level 1
  • 262 Views
  • 2 replies
  • 1 Helpful votes

Hi, hoping for some advice. New to SDA and fusion routers, have an issue whereby a VRF is unable to route to my legacy OSPF networks (to/from) on the fusion nodes which host the default routes so all OSPF traffic is following default route and being ...

Marco111 by Level 1
  • 189 Views
  • 3 replies
  • 0 Helpful votes

Hi all, Im having trouble getting my cores to route to my new WLC... I cannot ping the core from the WLC, and cannot ping the wlc from the core. Cores to WLC: 2 interfaces, members of PO71. VLAN allowed statement in use (allowed vlan 271)WLC to Cores...

when we attached 500 Mbps internet link to router V1000 then we got to know that V1000 has bandwidth limit of 250 Mbps only .hence 500 Mbps internet link does not work.1.how to check bandwidth limit of router and switch ?is it mentioned in data sheet...

knaik99 by Level 1
  • 343 Views
  • 3 replies
  • 0 Helpful votes

Hi eveyone, I might need some help to fix a very wierd issue. I needed to deleate some vlan in a switch, but unfortunately did it on the core. I let you imagine the chaos... now all the vlan are back up, but I have a really wierd case : I have a VM i...