Finding accurate answers to your questions and issues is always gratifying, but what if these answers are shared globally across different languages? The Cisco Community team has been working on a proof of concept (PoC) to take Accepted Solutions in...
The 9407 and 3750 are direct connect.SSH access fails due to an algorithmic issue.Please advise. 9407# C9407#ssh -l admin 192.168.10.10 [Connection to 192.168.10.10 aborted: error status 0] C9407# Jan 18 10:39:49.478: %SSH-3-NO_MATCH: No matching kex...
Memory utilization frequently exceeds 80%. The init process is using high memory. Does anyone know the cause and solution?
HELLO , I've configured an L2VPN point-to-point xconnect between the interfaces G1/0/13 and G1/0/11 using the following configuration l2vpn xconnect context testmember GigabitEthernet1/0/11member GigabitEthernet1/0/13 interface GigabitEthernet1/0/11...
Hi Team, I have a problem that I can't do ssh to these switches (mark red), but I can do ssh to these multilayer switches (mark green). Anyone have the same issue with me? The background is that all of these devices must be remote controlled from a ...
Hi everyone, I am trying to deny VLANs to each other and only be reaching server VLAN. My commands below is successful on packet tracer but failed during implementation. ip access-list ext DenyVlans_50permit ip 172.16.50.0 0.0.0.255 172.16.36.0 0.0.3...
SIT Router (Active Router) SIT DMZ (Standby router) Configuration: SIT (Active)int g0/0/1.20standby 2 ip 10.16.0.254standby 2 priority 110standby 2 preemptstandby track s0/1/0int g0/0/1.10standby 1 ip 10.17.0.254standby 1 priority 110standby 1 preemp...
Hi guys, I have a confusion about eBgp multi-hop, i always see just the multihop sets to 2, when using loopbacks and we have a router between peers, but what if we have a couple of routers that we can't count what we'll set as mutli-hop, is still 2 h...
I am having a hard time figuring out what I am missing here. But essentially I have a cisco 2960x switch with the SDM profile for routing enabled and IProuting enabled in the config. I have 2 Vlans (vlan 2 network computers are on 192.168.2.x 255.255...
Hi,As shown in the picture, each industrial PC is connected to the L2 Switch (No VLAN). The customer wants to install a data collection server and a data monitoring server. The data must be transferred from the industrial PCs to the data collection s...
Hi, hoping for some advice. New to SDA and fusion routers, have an issue whereby a VRF is unable to route to my legacy OSPF networks (to/from) on the fusion nodes which host the default routes so all OSPF traffic is following default route and being ...
Hi all, Im having trouble getting my cores to route to my new WLC... I cannot ping the core from the WLC, and cannot ping the wlc from the core. Cores to WLC: 2 interfaces, members of PO71. VLAN allowed statement in use (allowed vlan 271)WLC to Cores...
when we attached 500 Mbps internet link to router V1000 then we got to know that V1000 has bandwidth limit of 250 Mbps only .hence 500 Mbps internet link does not work.1.how to check bandwidth limit of router and switch ?is it mentioned in data sheet...
Hi eveyone, I might need some help to fix a very wierd issue. I needed to deleate some vlan in a switch, but unfortunately did it on the core. I let you imagine the chaos... now all the vlan are back up, but I have a really wierd case : I have a VM i...
HiI'm curious to know what you think is the best device for shaping traffic, especially when dealing with high volumes like 100G. Would a router be the top choice, or do switches handle this well too?I know that cisco 4500X and Cisco 6816 switches ca...
Hello in our company, we have two C6840-X-LE-40G that are VSS and we want to police traffic on this Switch. I searched and found out that we should use the below command so that the shape works correctly # platform qos police distributed loose/strict...
