Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

 
Labels

Forum Posts

Resolved! Routing path

Hello,I have topology like this picture where we have 2 WAN connection to bridge LAN1 and LAN2. We use OSFP for the routing and we have NPM (from solarwinds) to monitor WAN connection from LAN1.In the NPM i create 2 node with ip 10.100.1.2 and 10.101...

hs08_0-1710811110707.png
hs08 by Spotlight
  • 112 Views
  • 2 replies
  • 0 Helpful votes

I am looking for official datasheets\specifications of which power supplies are compatible for the Cisco 4431 router, which supports dual redundant power supplies. I am unable to find any official information.For example PWR-4430-AC vs PWR-4330-AC. A...

ramstyler by Level 1
  • 146 Views
  • 1 replies
  • 0 Helpful votes

I have three WANs; one is the primary and the other two are backups. Primary = dhcp; Secondary = Cellular0/2/0; Tertiary = Dialer1The routes are as follows:ip route 0.0.0.0 0.0.0.0 dhcpip route 0.0.0.0 0.0.0.0 Cellular 0/2/0 251ip route 0.0.0.0 0.0.0...

emuman100 by Level 1
  • 445 Views
  • 15 replies
  • 0 Helpful votes

Hi,I would like to confirm if the boost license upto 1.5 Gbps from the data sheet only supports onboard Gigabit Ethernet Interfaces and not Port channels? We have 400 Mbps bandwidth but ISR 4321 only limits it to 200 Mbps. We isolate the issue and it...

HiI'm trying to configue web ui on a isr 4331 router.IOS XE is version is 03.16.06.S, which might be ancientIOS version is 15.5I can connect to webui but the page isn't graphical, just a list of cli commands.Any suggestions.I bouhgt the router to stu...

J-Dread by Level 1
  • 278 Views
  • 4 replies
  • 0 Helpful votes

Hello, In past there was option to check flash from ROMMON - https://www.cisco.com/en/US/docs/routers/access/800/850/software/configuration/guide/rommon.html via fsck command In nowdays this option is completaly missing, I was doing this check on ISR...

Hi Team We have a pair of ISR4451s, with  IOS XE Software, Version 16.12.08, but, i think they have reached their throughput limit, based on some articles i have read and the output in the screeshot...  Monitor CPU Usage on ISR4300 Series - Cisco Al...

wladmirmendozandc_0-1709238733936.png wladmirmendozandc_1-1709239056506.png

Hello,I'm having some issues with policy based routing on an ISR-4451, IOS ver. 3.16.06SBasically, the goal is to redirect internet traffic for a specific set of devices to a different next hop, while leaving internal traffic and all other devices on...

Jake S by Level 1
  • 152 Views
  • 4 replies
  • 0 Helpful votes

The output below is from the show policy-map interface command. I was reviewing this and was wondering if this device's bandwidth is being restricted by this policy. We have a 100mbps connection for this router. I noticed the bandwidth allocations do...

ryders1 by Level 1
  • 80 Views
  • 0 replies
  • 0 Helpful votes

Hello, We have 2 routers (Cisco 4331). They are programmed exactly the same. The bootflash available space is different from one another. We have verified the bootflash has the exact same files. Can someone explain why they are different . Thanks!   ...

sacapano_0-1708701863105.png sacapano_1-1708701884164.png
sacapano by Level 1
  • 203 Views
  • 5 replies
  • 0 Helpful votes