Finding accurate answers to your questions and issues is always gratifying, but what if these answers are shared globally across different languages? The Cisco Community team has been working on a proof of concept (PoC) to take Accepted Solutions in...
I have an ISR4431 router, and related setting:ip access-list standard toGCP10 permit 10.136.0.0 0.0.127.25520 permit 10.136.128.0 0.0.127.25530 permit 128.231.0.0 0.0.31.25540 permit 128.231.32.0 0.0.31.255!route-map toGCPmatch ip address toGCP!route...
I am working with ISR 4331 in Packet Tracer 7.3.0. Although the router has 3 Gigabit interfaces, which I can configure and switch on, Packet Tracer only allows connecting 2 interfaces (using the connections button). Is this a bug of Packet Tracer? Is...
I have a location with a 50Mbps MPLS Circuit. I have been investigating reports of slowness and I have found on their WAN interface a bandwidth of 5000. This interface also has a QoS policy set on it. The QoS policy has a cir 10000000 (bps). I believ...
Hi all,I have a scenario where customer wan link is upgraded from 60 mb to 80 mb and customer is reporting performance issues now.On wan inter 80 mb QoS policy is applied , 56 for dscp ef premium class and 22 mb for standard class .I am seeing violat...
I dont have a support contract, so just throwing this out there in case it makes its way to the right set of eyes.Platform is a 4461, Cryptomap is applied to an add-in 10gb card, te1/0/4Comming from 17.9.4a - no issues here.Upgraded to 17.12.03 - VPN...
Hi guys, I have 4331 router IOSXE 17.9.4.a version I configured my 4331 ISR with Bridge domain and configured at 2 physical interface that bdi interface but when I finished the configure and try to ping with gateway I cannot ping via bdi interface...
Hi, good day, can anyone please advise whether need to purchase performance license to upgrade ISR 4331 throughput from default 100M to 300M ? Thanks in advance!
I have a large iWAN (ISR4451's) install. I have a new P2P circuit (between 2 buildings) but I can't get my iWAN routing to obey my static route. Below are the running configs for my switchport on my Nx9K and my 3850 switches, along with the tracero...
platform hardware throughput level 1000004331 hardware throughput level is 100mbps so is this an aggregated throughput for both direction traffic 50 In and 50 out or 100 Mbps in and 100 Mbps out.
Hello Team,I'm facing a challenge to apply a patch on the Cisco ISR4331. See the below error message from the router. SIMBA-RT#install add file bootflash:isr4300_cpld_update_v2.0.SPA.bin activate commitinstall_add_activate_commit: START Wed Mar 27 11...
these routers are direclty connected via point to point connection. When I try summarization, only ip route x.x.x.x x.x.x.x null0 with network statement works for me. When I use the aggregate address command I dont see summary route in route table....
I'm in a tough spot and currently having an issue with configuring a GRE over IPsec in my personal project. I think the configurations are right based on the verification commands that I used which are: show crypto isakmp sa and show crypto ipsec sa....
Hello Everyone. I'm looking to utilize the "show processes cpu monitor" task to view and validate cpu services and usages on a Cisco 4461 Router with IOS version 17.06.05.-I go to use the command and will show the cpu utilization for the first 5 seco...
Dear Expert,Hope all is well.One of cisco route 2921 reboot it unexpectedly and upon checking, we find out below result:cisco router reload reason bus error at PC 0xB0D0B0D, address 0x0.the firmware version: c2900-universalk9-mz.SPA.157-3.M8.binthank...
Hi, I have the following setup: Router 4331: G0/0/0 - internet connection G0/0/1 - Internal network. g0/0/1.10 - vlan 10. ZBF is configured to internal zone (internal network), external zone (internet connection). SW SG300 Gi1 - mode access - ...
