Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

 
Labels

Forum Posts

Hi,Is it possible to configure an MPLS VRF without the use of RDs?  I have tried to get this to work in a lab but have been unsuccessful (I have always had to use RD to get it to work)If I were to set up a MPLS VPN between a Nexus switch which has VR...

CiscoNutt by Level 1
  • 3340 Views
  • 14 replies
  • 0 Helpful votes

Hi Guys,I have 2 pairs of Nexus switches, each pair at each location. They connect between 2 locations with 2 x layer 3 links, as shown in the diagram.I configured EIGRP routing for both sites for these 2 pairs. The EIGRP routing works; my question i...

HiI'm facing some issue while useing ASA in gns3.....i have already attach the gns topology in which i'm not able to get the console of asa also i have attached the snapshoot in which u can see BOOTING THE KERNEL but in other window of asa console cl...

I am trying to configure DHCP so that it can use two physical ports on a Cisco Router. I would like to use two ports for redundancy and believe that the only way to do this is with BDIs because (1) the entire network on a subinterface must match the ...

brberg05 by Level 1
  • 178 Views
  • 2 replies
  • 1 Helpful votes

My names Terry, I'm a bit new here and new to Cisco ACI.Wanted to ask a question about L3Out within the Logical Node ProfilesI have ipsec tunnel between 2 palos that are connected to my fabric. (before my time )The Palos are connected to two BL's wit...

Hello panel I would like to know if there is a way for my problem I removed the enable secret mode on my router now when I access the router with my user account I cannot switch to privileged mode it tells me when I type enable it tells me error in a...

I'm a bit of a newbie with this Cisco stuff, so bear with me. I have set up port forwarding as follows:ip nat inside source static tcp 10.38.48.21 28919 159.196.177.138 28919 extendableI do know that UDP works since I can connect to all applications ...

exulan by Level 1
  • 204 Views
  • 4 replies
  • 0 Helpful votes

I have the following topology in EVE-NG:My goal is to allow Customer 2 clients (VPC4 and VPC5) to connect to Customer 1's FTP server.ISP router has the following configuration:ISP#show runBuilding configuration...Current configuration : 3520 bytes!! ...

cosmingrosu_1-1710094292254.png

Hi dear experts,I am having problems to configure and a lack of understanding the technique.My setup: ISP via DOCSIS to modem (in bridge mode) to the RV260 router. Behind the RV260 are a Catalyst 9115 and several Clients connected by LAN (1GB copper)...

familieboehler_0-1708856872819.png familieboehler_1-1708857123370.png familieboehler_0-1708857975427.png familieboehler_1-1708858382029.png

I have three WANs; one is the primary and the other two are backups. Primary = dhcp; Secondary = Cellular0/2/0; Tertiary = Dialer1The routes are as follows:ip route 0.0.0.0 0.0.0.0 dhcpip route 0.0.0.0 0.0.0.0 Cellular 0/2/0 251ip route 0.0.0.0 0.0.0...

emuman100 by Level 1
  • 445 Views
  • 15 replies
  • 0 Helpful votes

Resolved! HSRP

Hi @All I made a demo HSRP lab with the below setup:R1 connected to Switchport E0R2 connected to Switchport E1VPC connected to Switchport E2R1 connected to a tap interface tap1 (192.176.1.1)R2 connected to a tap interface tap2 (168.172.1.1)Conf of R1...

ashz14387 by Level 1
  • 201 Views
  • 4 replies
  • 0 Helpful votes