Finding accurate answers to your questions and issues is always gratifying, but what if these answers are shared globally across different languages? The Cisco Community team has been working on a proof of concept (PoC) to take Accepted Solutions in...
Hello Cisco Community.I hope I could make myself clear, cause my homelanguage isn' t english.I have SG350-28P and two internet connection, witch connected with Mikrotik router, witch doing NAT.My goal:Mikrotik 1 - let' s say vlan10 and 192.168.0.1/24...
Hello community! I hope everything is well in your life.I have 2x ASA 5515-X and I was using Active/Standby before and it was working great.We moved in a new datacenter and in this datacennter they have 2x gateway switch.They gave me 1 uplink cable f...
In Packet Tracer I want to configure Cisco ISR4331 router to use RADIUS authentication for vty lines and console..Maybe it is limitations of Packet Tracer or limitations of my understanding AAA topic, but can it be configured completely without any l...
I used below ospf routing (multi layer ports are no shutdown state)roue#multi-1int gig1/0/1ip address 172.1.6.129 255.255.255.252no shexitdo wr#multi-2int gig1/0/1ip address 172.1.6.133 255.255.255.252no shexitdo wr#routerint gig0/0ip address 172.1.6...
Please help and suggest. And sometimes I got correct APN name but not the right IP address. Any ideas? Ex. APN : AA, IP Address a.a.a.a APN : BB, IP Address b.b.b.b ----------------------------------- IR-Test#show cellular 0/4/0 Profile Profile 1 = I...
Hi,we have a ASR920 facing an ASR9K with 2 10G Link.We have configured Port Channel on ASR920 like this:interface Port-channel1description ***LAG***no ip addressno negotiation autoservice instance 1 ethernetencapsulation untaggedl2protocol peer stp d...
Hi all, We have two Core N7K running fine and on one of the C9407R we get these error logs few times a day, looks like osfp/bfd flapping but i cant detect the reason: 21:13:21.576: %BFDFSM-6-BFD_SESS_DOWN: BFD-SYSLOG: BFD session ld:24 handle:2,is ...
I'm trying to generate a core dump to the bootflash but keep running into issues. I keep receiving error 'write core not implemented' after running 'write core' from enable mode.What is the simplest way to do this? The current image is asr1000-univer...
i have a 2960 with routing enabled i would like it to route traffic like port 80, 433 ... but send all other traffic to an other router / firewall (isr c1111) for routingcan this be done in some way? sopc1 vlan 1pc2 vlan 2if pc1 calls a http side on...
I have 3 routers 2 of which are running EBGP. These 2 are getting a default route which is being redistributed into OSPF. OSPF will then advertise this default route to the 3rd router. On RTR1 i am using default-information originate and on RTR2 i am...
Hello Guys, I am currently having a minor issue with the ASA Firewall i cant get the ping reply to get through the firewall. It might be the NAT issue but i cant tell because i am too inexperienced. I can see the packets going past the firewall and w...
Hello Guys, ive been strugled with this problem for a while, the image bellow shows a simple diagram for the network.Router GIRASOL = CISCO1921 (this is the router im working on.)Router CANTV = this just simulates the ISPs interntal routing that conn...
A question about Cisco 3850 TCAM or Nexus 3064 TCAM The entry of the TCAM for PBR, when configuring it, what does it exactly mean?The entry means that ?: "The number of source ip subnets that we are allowing in the access list that will match the PBR...
Hello everyone,I am having difficulty with coming up with the correct ip route command to implement on each of the routers in order for the network on router 2 to be able to communicate with the vlans on switches 0 and 1.Router 0:f0/0 - 200.200.201.2...
Hello,I have two pictures above with topology and addressing and vlan table I have done the ip addressing according to the picture but i am confused with S1 vlan 4 and S2 vlan 4 with vlan 4 in the vlan table why the ip address so different and i hav...
