Hi Guys, I've recently had to adapt an 887 to work at one of our sites, which has a HFC connection delivered to an ISP provided modem. As this particular 887 doesn't have a WAN port, I've had to setup one of the LAN ports as a WAN port. After some r...
Forum Posts
hello, I was wondering how to know if a technology is supported on my cisco router.I have a C892FSP with IOS 15.4(3)M4, advipservices and c800-universalk9-mz.SPA.154-3.M4.bin system image fileI was browsing in https://cfn.cloudapps.cisco.com/ITDIT/CF...
I have a 3550-12g running IOS v12.2(25)SEE2. I have created an ACL to apply to a VLAN interface. Here is the ACL:ip access-list extended Block_Access deny ip 10.31.170.0 0.0.0.25510.3.140.0 0.0.0.255 deny ip 10.31.170.0 0.0.0.255 10.5.140.0 0.0.0...
Resolved! ASR-1002 X Default IPSec throughput?
Dear All, I want to check the default IPSec throughout for ASR-1002X router without any security or performance license?can you please update me the same..Regards,Ranjit
Hi folks. I have a cisco 1841 router and this is my setup:patch cable from my ISP router to fa0/0 of my cisco router.fa0/0 = Internet address is 192.168.1.116/24Broadcast address is 255.255.255.255Address determined by DHCP from host 192.168.1.1For f...
We are currently having problems with the routing where the route redistributed into EIGRP is being learned by the peer as Internal instead of External. Any help will be very much appreciated! In Router A, 10.122/16 is learning via External which i...
Resolved! Routing Options Question
If I have a single managed Switch with some devices setup in VLANs, but also a few that arent in a VLAN (VLAN1 by default I guess, but nothing VLAN configured on their access ports, and I want to get all traffic from the switch up to the Router and t...
Hi All, We have DMVPN configured with 2 HUB routers and 90 Branch spoke routers. Few times i saw below messages on my HUB router when i issue #show DMVPN. They go away in few min. Not sure why they generated. ALL out branch router Tunnel IP start a...
HUB --- ISP ==========branch 1 and branch 2 Underlay I have configured RIP/static.. tunnels are up and overlay i have configured OSPF.. Underlay is up.. tunnels are up and ospf neighbors are up..but i'm not able to learn other branch routes.. could ...
Resolved! OSPF not working
I have two routers connected with serial interfaces and to begin with I was unable to ping either router, anyway I want to configure OSPF 100 with the routers on area 0 the current configs are Router 1:Building configuration... Current configuration ...
Hi.. i am looking to upgrade ASR 1002, 2RU router from software ver. asr1000rp1-adventerprisek9.02.04.00.122-33.XND.bin to asr1000rp1-adventerprisek9.03.16.08.S.155-3.S8-ext.bin. Also running current Rommon ver 12.2(33r)XNC.Please confirm if i would...
Hello, I got a Cisco 1921 router, with 2 gigabit ports, and my ISP gives me a 1gbit/200mbit connection, so today I went for a speed test and I get the results between 90/90 and 280/200(after the Cisco 1921), My setup is the following-> ISP Router ->...
Resolved! MPLS QoS
Hi, we have lan switches 9300 and mpls between them, everything is internal LAN. Does it make sense to add " auto qos trust dscp" on the connected interfaces btw those switches? As I read mpls does carry 3 bits of dscp into packet, but not sure do i ...
Hello community,I need to establish a L2 VPN over a L3 Network.The Goal is, to span an existing VLAN from a on PE Router to the other.The gateway of this VLAN is also the PE Router (no CE Router). See picture.I currently can only simulate it with GNS...
Hello, Can we terminate 2 different ISP (e.g. 10+10 Mbps) on one router to achieve 10 Mbps in load sharing/load balancing and high availability both ? Option 1: - Internet connectivityOption 2: - Point to Point connectivity (leased link)
