Hello, Sorry but can't seem to find a good title for my question, you may help me with that. I have, as posted in the image:In my backbone, I have a PE that is connected to a switch (Switch 2). This switch has many clients connected to it and is perf...
Hello,Can someone tell me the difference between a 1941 Router and a 4321 Router? Thanks
i have 3 routers connected as shown in figure. I have given a command of PAT on r2. ip nat pool pat 25.1.0.1 25.1.0.100 prefix-length 24 ip nat inside source list 2 pool pat overload Standard IP access list 210 permit 1.1.1.0, wildcard bits 0.0.0...
I am doing sub netting and want to confirm that if my method is correct or not. Suppose we are to design a network that has 2 departments. Department 1 has 32 number of hosts and department 2 has 64 number of hosts. We are given the following IP:192....
Hi everyoneI have a extraordinary question I have one hub and many spokes already configured (single DMVPN, EIGRP, IPSec)And i want to reconfigure my network as Dual HUB, dual DMVPN. Is it possible to make one of the spokes to be HUB2 and still stay ...
Hi,i have made lab with1 HUB and 2 SPOKE phase 1 dmvpn over ipsec .Also rip routing protocol activated in points. Local networks can access other sites with rip.I also want they can be accessed to the internet over the nat .Any helps appreciated.Her...
I downloaded and installed the 5921 ESR and requested a demo license through the cisco portal. The problem I am having is that there is no way for me to disable the smart license feature? The command "no license smart enable" does not exist. Withou...
Hi everyone! Im doing some labs about EIGRP and convergence when a link fails. This is my topology and in router 4 f0/0 interface i have the 8.8.8.8 IP address . In this topology the metric calculation is based on delay only, so all links by default ...
Hi all,I have a multicast network like this: +-----+ | SRC | +--+--+ |----+----+----+---- | | ~ ~ | | +--+--+ +--+--+ | R1 +---+ R2 | +--+--+ +--+--+ | | +--+--+ +--+--+ | RCV...
Hi everybody! For the past weeks, I´ve been trying to figure out what´s happening at one customer´s network. It has 2 fiber connection with the same ISP, one connection with pseudo-fix IP and the other with dynamic IP. The Cisco3945E is behing both I...
Hi community,Green hand, first question here, probably a naive one, but I searched and couldn't find the answer. I'm not sure if this is the right board to ask. If not, please kindly let me know which one I should post to. I'll try to provide as muc...
INE foundation lab 1 - DMVPN eigrp keeps flappingHello, i am working through foundation lab 1 and I got to the DMVPN phase 3 portion and I got stuck. R1 is the hub, R5, R9 and R10 are the spokes. When I enter the solution on the routers, the link fr...
Hello Experts,I need a helpful advice regarding VWAAS-RTU-1300 and ISRWAAS-RTU-750 license. Recently I've purchased a Cisco ISR 4331 router, with which I have got these two licenses. Now I've done google several times about these license, but couldn'...
Hi, woundering if someone have comeacross this issue and can explain why it's working on some platforms as I have not been able to find a document on CCO that explains this behaviour.The issue is that the configuration fails when putting a simple egr...
Hello, recently I deployed Cisco 2811 router as CME, I have several phones and computers operating on different vlans (VLAN 10 VOICE 10.111.10.0/24, VLAN 20 DATA 10.111.20.0/24). I created two subinterfaces on the router with dot1q encapsulation and ...
