Hi, This is the Error i got while booting, It is a new router. The router is not going beyond "*Nov 16 10:53:21.683: %LINEPROTO-5-UPDOWN: Line protocol on Interface Embedded-Service-Engine0/0, changed state to down" IOS Image Load Test __________...
Forum Posts
I'm very new to Cisco routing. I have a 7100 series router and a new ISP that will advertise our IP block. I'm trying to figure out how to configure the router to allow us to use the IPs from our block. Any pointers on what I'm missing would be gre...
Hi all, Does anyone know why the ospf design dictates that we have all areas connected to the backbone and that areas that are dis-contiguous be connected via a virtual link? When I tried configuring an area that wasn't connected to the backbone, I ...
Resolved! Dual internet implementation with Router
Good day everyone, i need some advice on best practice for the following scenario; - we have 2 CE routers ISP owned providing MPLS access to our WAN - we would like to install 2 routers and load balance between them which should also provide redund...
Dears, I am facing the below error with ASR903 upgrade even i am following the procedure in the below document. Error message: --- Starting ISSU compatibility verification ---FAILED: ISSU compatibility check failed*Dec 4 11:20:33.950: %INSTALL-3-OPE...
Hello i am having some trouble trying to setup a network with OSPF and BGP, this is my first ever attempt. I have 2 ISP networks and 1 router connected to both. I have configured OSPF configured on the router "Marketing, Sales, Admin" and BGP on "Adm...
Resolved! pppoe client and IOS 15
Hi,The pppoe on IOS (15 version) does not work (when using 12.4 version- everything is OK)I have tried it with c880data-universalk9-mz.151-1.T.bin, c880data-universalk9-mz.150-1.M3.bin, c880data-universalk9-mz.150-1.M2.bin - DOES NOT WORK.But it DOES...
Resolved! OSPF Vitual Link Issue
My Topology.Before creating OSPF Virtual Link between R1&R2 , routing table getting inter area route (circle with red color). I understood with no doubt. The table belong to R2 Router. But, After creating OSPF Virtual Link between R1&R2 , routing tab...
Hello,why do we need to use broadcast instead of multicast in RIP? As far as I know multicast is better than broadcast because only communicates with certain devices that are configured with RIP so what is the goal of using: ip rip v2-broadcast? Than...
Resolved! AD 190 for EIGRP external static routes?
While doing practice questions for CCNP, I came across one that had as an answer the AD for redistributed static routes in EIGRP at 190. I also recall having this heard mentioned before. I tried to reproduce this in GNS3, but- the local router alread...
hi, i have installed ASA 5550 and every thing works fine, one day i noticed that my ASDM is not working. when i try to connect it gives me error " unable to launch device manager from xx.xx.xx.xx ip " i have enabled http server and also http xx.xx.x...
Hello, My topology :My configuration : R1 : BOX1#sh runBuilding configuration...Current configuration : 2022 bytes!version 12.4service timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname BOX1!bo...
Resolved! ebgp routing
Hello,Quick and basic question. We will be setting up an ebgp neighborship with one of our vendors. We will be advertising 10.0.0.0/8 and some other class B networks to vendor through this neighborship. Vendor will be advertising 10.169.0.0/20 to us....
I'm working with internal network 192.168.7.0/24 and default gateway is 192.168.7.254 (Our main ISP). Now we have another ISP. I want to make our secondary ISP to work only when our Primary ISP is down. Can this be achieved and if yes, how?-Thanks.
I have 2 device (cisco Catalyst 3850 and Cisco Catalyst 4500 in VSS mode) I try to configure a GRE Tunnel from this device but the tunnel doesn't work. If i try to build the tunnel from the Catalyst 3850 to Cisco Router 1841 with the same configura...
