Hello everybodyI am trying to setup some routing rules in my RV325 router.I want to route all data from a subnet to a vlan which I created previously. But in the routing settings I can't choose my vlan in the interface row (see picture). Am I missi...
Hi all, I have an issue that ISR 4331 {ISR Software (X86_64_LINUX_IOSD-UNIVERSALK9-M), Version 16.9.1, RELEASE SOFTWARE (fc2)} creates an additional virtual access interface when a dialer is mapped to a gig interface when the E1 card (NAME: "NIM subs...
Hi i have 3925 router and when i want to add new eigrp i get massage too many IP routing processes . Could not create the router process how can i solve this problem? how you thing if i upgrade ram 1 gb to 2 gb it solve problem ?
Dear all, I am beginner for network and some my question is duplicate and very bad to understand.Please forgive me.I would like to ask about DMVPN and IPSec. I have the network diagram for our network. We have 2 DC .One DC1 and our branches have cisc...
Does anyone know of a list or location of items that would be supported in Prime that are not Cisco? Third party that is -
Hi, I have the below topology in my prod environnement. My objective was to establish EIGRP 10 between the routers and L3 core switches but, The EIGRP between the Router and the L3 Core Switch in "Backup"/DR site is OK and functional. But, when I act...
Hello Experts, I need help...urgently i created a normal GRE tunnels on two routers!(routing protocol: EIGRP) i can see that one side EIGRP Tunnel is up and also showing in eigrp neighbour but other side tunnel is also UP but not shwoing eigrp ne...
Hello, We have two sites which are connected with a optic fiber access. This is supposed to be a 2Gbs link (in order to replicate data) . Our provider has confirmed there is no issue on the access, so we're almost sure that the issue is probably on...
Hey guys, I have 3 sites; Parramatta, Chatswood and Ryde. I need to create an ACL to block VLAN 10 (Student-Staff VLAN) talking with VLAN 20 (Admin VLAN). The VLAN's will still need to be able to talk to their corresponding VLAN across sites. The sit...
Hey guys, Based off the following design I have to: Isolate the Student Staff to one VLAN and the administration network to another VLAN at each site. (Site on the left is Melbourne, in the middle is Sydney and on the right is Brisbane) The adminis...
Hi, i have this config and output: router bgp 1111 bgp log-neighbor-changes neighbor 172.30.0.10 remote-as 700 neighbor 172.30.0.10 soft-reconfiguration inbound neighbor 172.30.0.10 route-map local-pref in neighbor 172.30.0.10 filter-list 1 out...
hi guys, i am fresh in Cisco devices. i got a ASA5506X and want update my domain to NameCheap. i followed https://www.namecheap.com/support/knowledgebase/article.aspx/29/11/how-do-i-use-a-browser-to-dynamically-update-the-hosts-ip and successfully b...
Hi, I have an asr9010 running IOS-XR 6.2.3 and configured 2 VRFs on it. I got an error when configuring static route from default and VRF-01 to sub-interface belongs to VRF-02. Below is the configuration, and the last few rows are the error messag...
Dear All, I am using cisco 800 series.i create int vlan in router and connect to switch with trunk port. i connect switch and create trunk port and allow all.and i create access port and create vlan.i plug my pc to switch and i ping to my gatwe vlan ...
I have an ASA 5506-X that I need configured for an outside static IP on GigabitEthernet1/1, as provided by my ISP. IP: xxx.xxx.xxx.118 SUB: 255.255.255.252 GATEWAY: xxx.xxx.xxx.117 DNS1: yyy.yyy.yyy.yyy DNS2: zzz.zzz.zzz.zzz ISP modem does not provid...
