Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Don't miss this Cisco Catalyst 8000 offer

 
Labels

Forum Posts

Finding accurate answers to your questions and issues is always gratifying, but what if these answers are shared globally across different languages? The Cisco Community team has been working on a proof of concept (PoC) to take Accepted Solutions in...

translator.png Asolution.png htlm-source.png insertcode(1).png
Kelli Glass by Community Manager
  • 10225 Views
  • 7 replies
  • 16 Helpful votes

Hello, Currently I’m looking for networking monitoring system for a DC Network which have ~200 nodes in 6 different geographic locations. All equipment is CISCO but different IOS version (IOS-XE,IOS-XR,NX-OS, IOS) Primary thing would be to monitor th...

from88 by Level 4
  • 466 Views
  • 2 replies
  • 0 Helpful votes

I have a 2811 running as my frame cloud for a home lab. I'm looking to use a NM-4T 4-port serial module to connect 1841s via WIC-1T cards. My 2811 is complaing that the NM-4T is not supported with my version of IOS. Can anyone tell me what verison of...

hrvxla by Level 1
  • 585 Views
  • 2 replies
  • 0 Helpful votes

Hi,I'm wondering what would happen if you connect two switches together with two up-links where all 4 ports are configured as access ports with portfast enabled? No BPDU Guard.I know all ports should transition into forwarding state immediately and c...

hello, need your help.i have switch cisco WS-C2960L-16TS-LL, Cisco IOS Software, C2960L Software (C2960L-UNIVERSALK9-M), Version 15.2(5c)E, RELEASE SOFTWARE (fc1). i cannot run command "port-channel load-balance":cisco01(config)#port-channel ?auto LA...

Yame by Level 1
  • 719 Views
  • 1 replies
  • 0 Helpful votes

Hi all, I'm having an issue that i hope somebody can help me with.  We are running a DMVPN environment and I have a couple of spoke offices that run voip over their tunnel to each other.  The issue is that we swapped the ISP in spoke A but now the la...

Cory King by Level 1
  • 2419 Views
  • 7 replies
  • 0 Helpful votes

Hey Cisco Community: I have a simple question.  Can I NAT just my guest wireless network, whose VLAN gateway sits on my L3 switches (HSRP), onto a public IP and not have it translated again by my second NAT, which sits on the last hop out of my netwo...

network.jpg

Question for the collective- When configuring multiple NTP server entries on a network device, if you do NOT use the "prefer" argument, does the network device compare the NTP packets from all entries and dynamically determine the best one to use? I ...

R_Acuti by Level 1
  • 6786 Views
  • 6 replies
  • 0 Helpful votes

Resolved! Route-Maps Issue

hey Community Team'Recently I am observing an issue with route-maps. Two links from different service providers are terminated on Router 2911. Default route is set to ISP1 & all traffic is working normally. When I applied route-map to send some traff...

Hi Forums,I have an issue that I'm hoping someone can shed a little light on. I have a 1941 with recent version 15.2-2T IOS happily working with a HWIC-4ESG (4 port Gig) card located in slot 1. When I add a HWIC-4ESW (4 port 100Mb/s) in slot0, then t...

 Hello, I am encountering this error when setting up persistent logging.switch(config)#logging persistent url ? disk0: Filesystem nameslavedisk0: Filesystem nameslavesup-bootdisk: Filesystem nameslavesup-bootflash: Filesystem namesup-bootdisk: Filesy...