Hi Community, I´ve a problem with a new delivered C1111-4p router. I just wanted to downgrade the IOS-XE to an other version. The IOS-XE which was installed from the factory in the bootflash: was "c1100-universalk9_ias.16.12.05.SPA.bin". So have co...
Forum Posts
I'm using CML, and I have 2 routers and a switch. I am trying set up EIGRP. on my router I have my two interfaces in my EIGRP instance and when I try to add 3 VLANS (192.168.10.0, 192.168.20.0, 192.168.30.0) the wildcard masks won't show up. when I d...
Hello,I have configured the EEM and IP SLA on router 2911 with the event "track state down".event manager applet Prueba3 event track 1 state down action 1.0 cli command "enable" action 1.1 cli command "configure terminal" action 1.2 cli command "int...
Hi TeamI need some guidance on Qos . our network is facing the high receive utilization for one of the branch site. During business hours its crossing the 95%. we have legacy Hub and spoke infrastructure. that means all the traffic should pass throug...
Resolved! Radius Server Dead
I get these periodically during the day on the router syslog. Feb 16 19:33:22.817 EDT: %RADIUS-4-RADIUS_DEAD: RADIUS server x.x.x.x:1645,1646 is not responding.Feb 16 19:33:22.817 EDT: %RADIUS-4-RADIUS_ALIVE: RADIUS server x.x.x.x:1645,1646 is being ...
Resolved! ISR 1100 features activation problem
Hi. We have two new ISR1111 (running on Version 17.5.1a) with bought licenses:Cisco 1100 Series with 8 LAN Ports, 200 Mbps IPSEC Throughput LicenseCisco 1100 Series with 8 LAN Ports, Security License We converted PAK licences to Smart Licences. Both ...
I have a location that has two 24-port switches whose IP addresses are (for example) 192.168.1.1 and 192.168.1.5. I would like to replace these two switches with a single 48-port switch and use IP 192.168.1.1 for the new device. The new switch will c...
Hello everybody, could anybody explain me about the MTU mismatch logic between IOS XE and IOS XR routers . I have 2 routers(IOS XE and IOS XR) that are connected directly. I've configured the ospf between them and got stuck in EXSTART state. As I kno...
Resolved! Bandwidth limit of a port
Hi TeamIf a port supports only 1 Gbps and has an inbound traffic of 600 Mbps and outbound traffic of 800 Mbps, will it exceed its threshold? How will the 1 Gbps port behave? Will it handle 1 Gbps for both inbound and outbound simultaneously, or will ...
I noticed that users loose connectivity on the network, when I do a continuous ping to my gateway (router) it times out for a few seconds and this happens every few minutes. Initially I thought the switch connected to the router was the issue but whe...
I'm working on a network to support VHF radios transceivers. The backbone uses DMVPN, and requires Multicast for base station discovery and replication of voice traffic between base stations connected to the DMVPN. Each base acts as both a Mutlicast ...
Resolved! CBS350 with modem Bell "Giga Hub"
Hi!I use the CBS350 switch with several VLANs (intervlan), everything works fine, except I have no internet.The reason seems to be that I will need to configure the routing of my VLANs on my modem, except that my modem does not seem to be able to do ...
Hello everyone please help me haw i could connect to router/switch via snmp?i can get information about ip add or link but i couldn't entry to router/switch.for exmaple snmpwalk -v 2c -c ^v%tb!4NX 200.200.200.2 1.3.6.1.2.1.1.3
Resolved! DMVPN 3 Phase
Hello every one here my all config, currently i can ping everywhere on my topology from everywhere, my question is i want check 3 phase working or not in my topology thanks in advance.ISP config interface GigabitEthernet0/0ip address 172.16.0.100 255...
i have a topology look like this and i already turn on the rstp configuration to each switch. then i set up priority each switch like thisLantai 6 (up right) : 28672Lantai 2 (up left) : 32768and Multi SW 10 (down) 40960 but, why Lantai 2 - Multi SW ...
