Finding accurate answers to your questions and issues is always gratifying, but what if these answers are shared globally across different languages? The Cisco Community team has been working on a proof of concept (PoC) to take Accepted Solutions in...
I am newbee to cisco technology and hence require your help in order to configure the router for the following network scenario so here it is ISP WAN IP : - 1 72 .2 4 . X . X/ 3 0 ie private class IP ISP Public Lan pool : - 1 ...
hi, Anyone has comment, why this PBC is not working ? interface FastEthernet0/0 ip address 192.168.1.1 255.255.255.0 ip policy route-map PM1 duplex auto speed auto!interface Serial1/0 ip address 200.1.1.1 255.255.255.0 serial restart-delay 0 clock...
Hi As we know, bgp route-policy controls if routes can be forwarded. Here are example: If route 10.1.0.0/16 is permitted to pass in route-policy, the route can be forwarded to pass. If route is10.1.0.0/24 under the same route-policy, can it be forwar...
Hello All, When we are configuring PBR in OSPF with CEF, it's not working but without CEF it's working. Is PBR working with CEF in OSPF ? If not then what is the reason ? ===================================================== IOS ver :-12.4 ========...
Dear All, I am looking for a solution where i can connect my Cisco router 2821 through a second ISP in case primary link goes down. The router has vwic-2mft-g703 installed. So is it possible to have second ISP connecting on this module so that i have...
Hello All, I had a question about the Archive command. when I enter Config t and go into "archive" I try to select the option for "path" but the paths it gives me are only network paths(ftp, http, https ect...) It does not show me local paths(d...
I am very confused on how to get accurate readings for SNR and other statistics on a per-interface basis on the Cisco CMTS platform. Here is the problem: I get the cable interface information, and use that same ID to correlate and walk DOCS-IF-MIB:d...
Dear all, I am facing issue with PPPoE connection this connection was working from the past 2 month suddenly one day stopped working. always getting log like bound or unbound dialer 1 interface with virtual interface 1 line protocol up/down dialer in...
Hello, Sorry if this is the wrong place to post this but: I am wanting to download IOS's for routers and Switches so that I can practice using them for my own personal training (using GNS3). Though when I go to download one for the below page it says...
Hi All, I am stuck in a situation where I have to add 1 IP phone 7965G to the network and make it work. The phones were working previously but the previous contractor when they left the site, they made a mess out of the whole network and nothing is w...
HI, How to enable IP accounting in ISR4321/K9. #sh verCisco IOS XE Software, Version 03.16.04b.S - Extended Support ReleaseCisco IOS Software, ISR Software (X86_64_LINUX_IOSD-UNIVERSALK9-M), Version 15.5(3)S4b, RELEASE SOFTWARE (fc1)Technical Suppo...
hello alli did in past a lot of L2TP connection between two end point.in this case ans with 2911 series with ios 15 and DATA license Activated.i The l2tp session does not establishe between a this 2911 and 7209.please FIND attached the topologie file...
how OSPF decides how to forward traffic?
I have a problem with a Cisco C888-K9I can not manage the EFM partthe command " controller DSL 0 " does not work
Hi, Please see the below route-policy commands: route-policy TO_ABC if destination in DEFAULT_ROUTE then drop elseif destination in ABC_1111 and community matches-any ABC_1111_COMMUNITY then passend-policy ABC_1111 and ABC_1111_COMMUNITY are combine ...
