Dear Team. How can we restrict the username and password configured on router only for telnet or only for ssh. Regards. Santosh M.K.
Dear Team. How can we restrict the username and password configured on router only for telnet or only for ssh. Regards. Santosh M.K.
I am running 15.4(2) vIOS and Cisco navigator states that 15.4(3) is needed to PfRv3? Can anyone tell me for sure that 15.4(2) will not work for v3?
Hi Team, I am just new on the BGP world, I am having trouble on Active Standby function of BGP protocol. Please see the details below. Goal: To establish active standby connection, If connection between R3 [50.50.50.0/30] and R1 [10.10.10.0/30] got ...
why serial port don't have mac address, and does it really create problem in frame relay when we configure access list. what was the reason behind it that serial port don't have mac address. why it broadcast first.
Hello Dears kindly assist on possible cause on below BGP issue. BGP session failed to be established with below error name proto table state since infoXXX BGP master start 10:23:26 Idle Received: Malformed AS_PATH a...
We are planned to upgrade our ILL bandwidth to around 600Mbps.Whether Cisco ISR 4451 router support the above mentioned bandwidth.Any other alternate models
how can we configure load balancing in bgp and how can we configured bgp with three isp with high availability
Hi, I have two sites (10.1.0.0/16 (6506e) and 10.15.0.0/16 (3750x stack)) connected together with a /30 link (192.168.254.5 and 192.168.254.6) over a dark fibre connection. Traffic is fully routed between sites with simple IPv4 static routes on eith...
HI all, I Have a 6509 router running in production environment, but I am planning to switch it to a 7604 router. While I dont have the problem of the config between them, it seems that from a unknown reason, there is some MPLS routers that exists on ...
Hi, Appreciate if someone can help to pinpoint what is my error when I configure 2 static routes in 2 routers for redundancy. But I can't failover to each other until I need to remove and re-add the route. I have 2 routers 2901 routers and connect...
Hello, Say Router A has a network of 10.89.0.1 behind it and Router B has network of 10.72.0.1 behind it. Would I have two create a static route on both routers for 10.89.0.1 to connect 10.72.0.1 or do I need to create only static route on router a...
Hi,I have created this config on switch.p dhcp pool CARLSON network 10.36.247.64 255.255.255.224 domain-name carlson.com dns-server 203.122.63.152 203.122.63.154 default-router 10.36.247.81!ip dhcp pool pool2 host 10.36.247.82 255.255.255.2...
Hello all, Mon architecture existante ci-joint n'est pas redondant. Etant l'admin réseau je suis en charge de fournir une solution avec le cœur du réseau redondant. A cet effet, j'ai proposé une solution et j'aimerais avoir votre avis, car je sais qu...
I have a Cisco C897VA-W running IOS 15.6(3)M When I load a config that previously worked on this model under 15.1 the router fails to complete the boot cycle. I have gradually loaded the config piece by piece and have got to the stage now where it c...
Hello, I need some help configuring a routing scenario below on the ASA Firewalls only between sites A and B as per diagram (see attached. It can be done using BGP or OSPF but need guidance on which is the best and simplest to configure and how it ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-07-2024 10:40 AM | ||
07-15-2024 05:07 AM | ||
07-13-2024 09:04 AM | ||
07-09-2024 05:41 AM | ||
07-03-2024 08:54 PM |
User | Count |
---|---|
10 | |
9 | |
9 | |
3 | |
2 |