Hi, RD value needs to be changed in PE router(ASR12K) in MPLS, what protocol we can follow? Any links is also welcome. Thank you
Hi, RD value needs to be changed in PE router(ASR12K) in MPLS, what protocol we can follow? Any links is also welcome. Thank you
Hello! So I found this 2811 Cisco router & wanted to hook it up in my house to use with my existing network equipment. I thought that it would be pretty straight-forward, but I can't seem to get it to work properly. I've looked online to find the co...
Hello Folks, One of our branch router is facing latency issues. Upon checking I found the circuit clean and utilization is normal. However, found lot of output drops. This is a 6M MPLS circuit. Solarwinds NMS is also showing Transmit discards on th...
Hi, We have some 4506-E switches using Supervisor 8 which we have configured with Reg variable as 0x2102 to pick the IOS we explicitly tell the switch. Please see the image. Even so, every time we reboot the supervisor, it enters into Rommon mode. ...
Hello all! I have an EIGRP Load Balancing challenge!! I've recently deplyed a second NX7K chassis to provide redundency in our network. Everything went all except for one minor EIGRP Load Balancing issue that I am facing. Here's the setup: VSS_6509_P...
Hi All We are trying to Migrate the our customer circuits from ATM interface to Ethernet without minimal disruption. We have around 20 odd customers hanging off the that ATM interface, each sub interface is for each circuit. What will be the best mi...
I have been given 2 subnets from the ISP, one subnet (/30) for the interface connecting to their equipment and another subnet (/28) to NAT our servers. The router is a ISR 4331 with right now just 1x SFP (connecting to ISP) and 1x GE (connecting to s...
There are two kinds of RD. One is under global mode, second is under bgp mode as below. What is second used for? Thank you router bgp 2111 vrf WWE rd 2111:222
Hi Here a topology, PE1 and PE2 have different RD value as the below in MPLS. From PE2, what command can be used to see routes which are from PE1 and are attached by RD 100:1? Thank you PE1vrf abcRD 100:1 PE2vrf abcRD 100:2
Hello All, What if we get same exact route from two ABRs?? From two ASBR ?? One from ABR & One From ASBR ?? Thanks, Prasanna Kumar Desireddy
Hi All, I want to build a setup with the following technology [GRE, L2TPv3 and Multicast]. Can you advise what Software IOS image I need to get for 2911 router; will c2900-universalk9-mz.SPA.152-4.M3 support all features of given technologies. Also...
I have two questions regarding this subject; first, why doesn’t it work when referencing ACL’s in two different NAT statements on a Cisco ISR router? !---Routing and interface configurations omitted--- !ip nat inside source list NAT_172.16 interface...
Hi, I am having CISCO 1941 router which has two ISP, and i configured auto failover of ISP. Now want to configure load balancing. Could you help me out to configure the same.
Hi. I have a Cisco ASR 1006 Router, with the the aux-port connected but i can´t configure the "line aux 0".. the line does not exist in the running config. http://www.cisco.com/c/en/us/td/docs/routers/asr1000/install/guide/asr1routers/asr1higV8/asr1_...
Hi, I woulk like to know if it's normal that the interface cellular 0 goes Up only when trafic want to pass on it ? I Use Gigabitehternet 0 like primary WAN interface and Cellular 0 interface like Backup. I'm using Wan Failover with IP SLA command....
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 12-05-2025 03:27 AM | ||
| 12-03-2025 07:46 AM | ||
| 11-13-2025 04:57 PM | ||
| 11-09-2025 09:51 PM | ||
| 11-06-2025 06:09 PM |
| User | Count |
|---|---|
| 9 | |
| 6 | |
| 4 | |
| 4 | |
| 3 |