Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Don't miss this Cisco Catalyst 8000 offer

 
Labels

Forum Posts

Hello All, Crypto feature is not coming up on the ASR... ON the data sheet its says that the feature is enable.. but its not coming up :( Router#sh verCisco IOS XE Software, Version 03.13.02.S - Extended Support ReleaseCisco IOS Software, ASR1000 Sof...

I have an ASR 1002x with 2 GIGe pipes setup bgp. Both ports have the ip access-list extended WAN_TO_LAN added as "in". I would like to add to that acl to block all traffic from the internet to those ports except for eq 443. The IP I want to control ...

mchance by Level 1
  • 366 Views
  • 4 replies
  • 0 Helpful votes

Hi There, I am having an issue with setting up PBR to make use of secondary ISP which is sitting idle. Here is our network topology! Gi0/2 - 10.10.10.1/24 LAN Subnet Gi0/0/0 - 200.200.200.1/30 ISP1 Gi0/0 - 100.100.100.1/30 ISP2 Default routes: i...

rmnr by Level 1
  • 1865 Views
  • 5 replies
  • 0 Helpful votes

If 880data-universalk9-mz.151-4.M4.bin is booted on CISCO881G-K9 below currently running ios 12 would advipservices permanent license still remain in effect? Cisco IOS Software, C880 Software (C880DATA-UNIVERSALK9-M), Version 12.4(22)YB2, RELEASE S...

wayfaring by Level 1
  • 407 Views
  • 1 replies
  • 0 Helpful votes

Resolved! NAT problems

I am having troubles setting up NAT, or what I believe to be a NAT issue, because I can ping from Gi0/1 only to Gi0/0 while Gi0/0 can ping anywhere on the Internet.The router is a Cisco 3845. There's two connected together, but here's the configurati...

Hi Team,  We have cisco 2901 model router in network for voice traffic. Currently one PRI line is terminated on router. This router was perfectly working till yesterday and all of sudden we lost the remote access. When we check the log by console the...

Hi , Im creating L2TPv3 tunnels between ASR 1001X and 1841,2811,3725. Tunnels between ASR1001X and 1841 , ASR 1001X and 2811 area formed. But it is not established between ASR1001X and 3725. ASR 1001X logs LAB-ASR1001X-R4# sh xconnect allUP pri ac Gi...

Hi Sir,  Please help to answer some questions below. 1. I'd like to get confirmation whether NIM-ES2-4 card can be installed later without powering off the ISR4321 router? 2. is it possible configure HSRP between 2 units of ISR4321 in active-standby ...

Hi Sir,  Please help to answer some questions below. 1. I'd like to get confirmation whether NIM-ES2-4 card can be installed later without powering off the ISR4321 router? 2. is it possible configure HSRP between 2 units of ISR4321 in active-standby ...

Hello everybody, we do have the follow problem. We have 2 cisco ISR4321/K9 (Version 15.4(3)S5). On the backup router the s2s vpn connection is stable and working on the primary router S2S VPN is working sporadically. We have checked everything and ca...

All, I've never done what I'm describing before, and because there may be proprietary information in the actual output, I have to be unfortunately vague, but here's the situation: A customer noticed an asymmetric path through his BGP cloud while inv...

We have a couple of 7606-S / RSP720 core routers, each populated with one X6724-SFP and three X6708 cards, and we're looking to replace them with something else, mainly due to the oversubscription limits of the X6708s being reached more and more ofte...