Hi! Where speed limit on ISR 4000 is applied? Is it sum of all traffic on all interfaces leaving the ISR? Do switch interfaces count? Do internal interfaces count? do inter-VRF routing count? What do these 50 mbit/s mean? Thanks!
Hi! Where speed limit on ISR 4000 is applied? Is it sum of all traffic on all interfaces leaving the ISR? Do switch interfaces count? Do internal interfaces count? do inter-VRF routing count? What do these 50 mbit/s mean? Thanks!
Based on the documentation, we are only allowed to have one hub Master Controller per domain ID? Is there a possibility to have active/active Hub MC's? If there are 2 DC's and the MC at the HQ fails what options do we have besides the Branch MC det...
I followed the cisco router dual WAN failover guide at http://docwiki.cisco.com/wiki/NAT_failover_with_DUAL_ISP_on_a_router_Configuration_Example If I remove the ethernet cable or shutdown interface Gi0/1 or the modem that is its gateway reboots or p...
Please can you help me to configure port forwarding in the router cisco 887vaI want to access my private ip from out side through my public ip using port 80i do all NAT commands no thing changedplease help menote : i have 2 public ip's I attached th...
Hi, I wondered if anyone has any experience in bundling 2 fibre broadband links together, we need extra capacity for a wireless network that is used for guest wifi and testing purposes. The single circuit currenly has a b/w of around 50Mb, but I was...
Hi I am looking to change my routing architecture Requirement Allow all traffic to go via the primary WAN Allow one route to go via the secondary WAN In the event of a WAN drop, everything to use the working link Current I have 2 exit points from my ...
Hello I am interested in knowing how do you determine if a T1 connection is necessary for your building or organization. The reason i am asking this question is because recently someone told me that their company purchased T1 connections for all the...
Hello Team, Below is ISIS database but output i can see the routes & neigbour UP, but it's not showing in routing table. What should be my next step. I am able to see all routes of R1 in R2 R1#show isis database R2.00-00 detail Tag area_0041: IS-IS L...
Hi, I connected Cisco 2960 and HP 1910 Switches together with default configs but ports didnt became UP.Then I assinged VLAN 200 on Cisco sites and ports was UP for a while and then a few hours later ports became DOWN again.whenever I do "shutdown a...
hello, I have my DHCP server that is in a Vlan of my VRF A and another Vlan in another VRF that contains clients When clients and server are in the same VRF control IP HELPER-ADDRESS x.x.x.x(ipofmyserverDHPC) is correctly Control IP HELPER-ADDRESS V...
We have 2960x switch (WS-C2960X-48LPS-L 15.0(2)EX4 C2960X-UNIVERSALK9-M) and have configured on access ports port-security, ip source guard (IPSG) and also DAI and DHCP snooping enabled globaly on switch. The problem is that when we configure the ...
Hello, I have a problem: class-map match-all HTTS match protocol http match protocol secure-http!policy-map QOS class HTTS priority percent 10 class class-default random-detectpolicy-map int class class-default shape average 10000000 service-policy...
Hello. Help me please. I am have Catalyst WS-C2960CPD-8PT-L, but can not found Power supply.. In description part no - PWR-ADPT=, But all photo in reseller web sites Power Supplys with round connector.. My Catalyst have 2 pin connector, see please at...
Hey there! I've inherited an older network at a new job I just started at and am wanting to get some insight into some router performance issues we're currently experiencing. In general, websites are taking longer than they should to load. Anything f...
The HTTPS server on the 2.0.6.0 (latest) firmware WAP200 wireless-G accesspoint only supports up to SSLv3; as a result it is unable to be accessed with modern web-browsers securely, as we're still quite a ways from the 2017 EOL support date, I would ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
09-23-2024 06:56 PM | ||
08-07-2024 10:40 AM | ||
07-15-2024 05:07 AM | ||
07-13-2024 09:04 AM | ||
07-09-2024 05:41 AM |
User | Count |
---|---|
12 | |
11 | |
6 | |
4 | |
3 |