Finding accurate answers to your questions and issues is always gratifying, but what if these answers are shared globally across different languages? The Cisco Community team has been working on a proof of concept (PoC) to take Accepted Solutions in...
In the following example: R1#show arpProtocol Address Age (min) Hardware Addr Type InterfaceInternet 10.0.0.1 - 0000.1111.1111 ARPA FastEthernet0/0Internet 10.0.0.2 0 0000.2222.2222 ARPA FastEt...
Hello,Does cisco ISR 4331 support reflexive ACLs?Is there another feature that will allow us to do allow only RDP through an interface and block incoming traffic but allow the connection of the RDP? Thanks,Omer Shtivi
We have a 25Mb connection going over a 10Gb link on a 3850-48P. We currently have it shaped to 25Mb with a nested QoS Policy:class-map match-any QOS-EF-OUT description QOS EF Queue match dscp af41 af42 ef class-map match-any QOS-VOIP-CONTROL-OUT...
I have a 10M WAN link between two offices, but I found that there is a tail drop and WRED drop. Just wonder why it was dropped under the max. bandwidth... I'm not sure whether there is a mis-configuration... <LOG>-------------------------------------...
Hello, Please let me know.We are planning to use C7201 as LAC, and ASR1001 as LNS. Required maximum number of connections is 5000.Is ASR1001 enough to support the number of connections?I refer the info here, but I don't know the meaning. Why the numb...
Hello community, I would like to change the firewall from Zywall (In my opinion a very bad one) to a cisco asa firewall (ASAv). But before I configure the firewall I have the overall noob question: How do I change the firewall in production when we...
Hello,Our 2811 Edge router is having extremely high CPU problems. IP Input is consuming 70% of the process during business hours. Cisco express forwarding is enabled. It only shows 50% but its currently before business hours. Id say even 50% is still...
Has anyone had any experience of configuring OTV on ASR 1100 series routersI am looking at a redesign of our two data centres, having had a hard sell on Nk7s we are struggling to work out whether we even require them.OTV had popped into the equation ...
i am checked one of production router FD is infinity... what it denotes?Sh ip eigrp topologyP X.X.X.X , 1 successors, FD is infinity, tag 64520 Via X.X.X.X(wan Ip) (419584/419328), Gigaethernet1/01and also found advertised distan...
Good day,To start off, I am new to Cisco and networking and am currently taking a course. I configured an ACL, per our assignment, to accomplish what the task was, and it worked but was not the standard ACL configuration command that the instructor ...
Hi Community,Can you guys tell that 7206 router support BFD fully? I found some bfd commands under (config)#router .... but i don't see show bfd or something to query the feature to get more information about the configuration and operation status.Th...
Hi,I have following configuration on the router.int g0/1desc Customer # 1. Need to rate limit to 100Mbps bandwidth of internet connectioninterface GigabitEthernet0/1.10encapsulation dot1Q 10ip addr y.y.a.a 255.255.255.192interface GigabitEthernet0/1....
Good morning everyone,I hope someone here could assist me with the situation I am facing, I am a network administrator who has been assigned the task of adding a secondary router to a redundant backup third party provided internet circuit. This route...
HelloAccording this link I configured ddns on my Cisco 877W router but it didn´t workhttp://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipaddr_dns/configuration/15-mt/dns-15-mt-book/dns-dyn-dns-supp-ios.htmlWith debug ip ddns I get the following inform...
Hi all, What are the best catalysts to buy for the ccnp switching preparation??am thinking about1 catalyst 29502 catalyst 3750thanks for your replies
.png "Hall of Fame"){kind=icon}
