I need your help which is better ? 3850 catalyst or 9300 nexsus for 10G SFP switch can work fiber or copper 10G for both price and performance
I need your help which is better ? 3850 catalyst or 9300 nexsus for 10G SFP switch can work fiber or copper 10G for both price and performance
Hi All, VPN tunnel monitoring: we are getting the following error while trapping the tunnel. Sending incorrect cikePeerLocalAddr & cikePeeRemoteAddr along with cikeTunnelStop trap due to which same ticket is being updated instead of creating new one....
Hi I am facing one interesting issue with ASR9K device. Below is my topology. Two different ASRs connected through a ASA. ASR9K------->ASA---------->ASR9K The routing between first ASR9k and ASA is ebgp. The routing between ASA and second ASR9k i...
Hello Engineers; I have a question on setting up the type of OSPF network for Ethernet interfaces facing the VPLS/WAN network. I've read recommendation to change the OSPF network type from broacast to Point-to-Multipoint and Point-to-Multipoint Broa...
Hi, I'm getting this message. %TCP-6-BADAUTH: Invalid MD5 digest even i I configured the same password for both routers. I'm using Cisco IOS XE Software, Version 03.14.01.S for ASR1001 router. Both routers are connected to same switch and on the sa...
Hi Please see the attached diagram. I have Site A (Existing) and Site B (New). Some users will be moving over to site B so we need to extend the network into site B. We have a 24Core fiber between the sites so the plan is to install a L3 switch at ...
Hi all, hope everyone is well !! I am looking into how to best design/configure dynamic routing between my existing MPLS WAN and internet WAN (iWAN) that I am going to deploy, please see attached diagram for an overview of the layout. At the data cen...
Is there a maximum configurable static NAT translations (not PAT or pools) - 1-to-1 NAT statements on a Cisco ISR 4000 series router running current recommended IOS code. I know, a firewall may be more optimal for doing huge numbers of static NATs. ...
Hi I have a site and we have purchased a 200mbps link for the ISP. We are looking for a router just to peer with the ISP using BGP, so that we can control what to advertise etc. What router is fit for purpose. I have seen a lot of 2900 routers used ...
Can you do QOS for voice on a Cisco 1921, I been unable to find a example config
Hi , I am confused in this because every other article have different views on this. 1. How many OSPF areas i can configure on 1 ABR ? i have L3 switch C3850 i need to configure on this device ,how many could be Possible. ? 2. How many routers pe...
Hi,I searched online for this, but couldn't find the answer.Thanks,Richard
Hi there, I'm wondering what's the most common deployment of metro network between two physically separated buildings ? Should they have the same subnet ? or a different one at each side ? thx Garry
Hi Guys, I have a question regarding the order of the "ip nat inside" statements on an IOS router. We have a situation where a network 192.168.1.0/24 needs to get to the internet and therefore we have the overload statement out Dialer. Then we have a...
On PT it is working well, but on real network it isn'n working. On real Network as a dhcp-relay, i have an 3750G Sw (Version 12.2(44) SE5, RELEASE SOFTWARE (fc1) Ip routing is on. All made as in the scheme, but i dont know why it didn't works. Somebo...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
02-06-2025 12:03 AM | ||
02-03-2025 09:24 PM | ||
02-03-2025 07:43 PM | ||
01-13-2025 09:53 AM | ||
01-04-2025 06:17 AM |
User | Count |
---|---|
17 | |
10 | |
8 | |
8 | |
5 |