Buy or Renew
Buy or Renew

Routing

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

Labels

Forum Posts

Start a conversation

Resolved! Cant ping sub interface gateway

Hey all,   Trying to setup a cisco router to work with 5 sub-interface vlans. Issue i am currently having is that a device on one network (192.168.10.100) cant ping the gateway IP of 192.168.10.1. The sub-interface is up as i can ping it from the rou...

EEM script not getting into "enable" mode

Hi All, I am having issues running my EEM script. The script is used to edit the prefix-list, based on the packets received at the interface. When I run the debug, I see that the script is indeed triggered but unable to get into the "enable" mode. A...

ASR 1006 GIG interface MTU issues

Hi All, Can you please advise if there any limit on MTU size for GIG interface on ASR 1006 router? I am able to ping P2P link with size 9082 but not with anything greater than 9082. SPA-2X1GE-V2 is the card type and its same at both ends. Please ...

Router reboot due to ZTP ?

I want to Know What is ZTP? Router#sh version Cisco IOS XE Software, Version 03.14.02.S - Standard Support ReleaseCisco IOS Software, ASR920 Software (PPC_LINUX_IOSD-UNIVERSALK9_NPE-M), Version 15.5(1)S2, RELEASE SOFTWARE (fc2)Technical Support: htt...

Issue Building an IP GRE Tunnel

I'm trying to build a tunnel accross the internet and seem to be having an issue with actually being able to ping accross the tunnel. Router 1 is a terrestrial link; Router 2 is a satlink with ping times avg'ing 600ms. Both routers are able to ping e...

Resolved! Max AS Path to accept from peers

can anyone advise on what cut off on AS-PATH length would be when accepting routes from peers,  looking through some of the received routes the AS+PATH is pretty high and I would like to limit this down, is this strictly necessary ? If so what would ...

shaps by • Level 3
  • 11177 Views
  • 10 replies
  • 0 Helpful votes

NAT statements & SSH access

Router is a recent C887VA running 15.3 When I have my NAT statements in place for ports 80 and 443, I have no external SSH access. It actively refuses my connection. If I remove these 2 lines (154 and 155 in the attached txt file) ip nat inside sourc...

Cisco 2800 Router "show run" doesn't work.

We have Cisco 2821 router on production. It is configured as voice gateway with FXO and PRI cards.IOS is : "flash:c2800nm-spservicesk9-mz.124-20.T4.bin"It was up and running since long time, almost more than 33 weeks.Suddenly, it stopped processing  ...

Resolved! MPLS routes to advertise from CE to PE

Hi, I am new to MPLS and requirements.   We have a new MPLS circuit being deployed between two sites.  The ISP has asked me for what Routing Protocol , AS number and any LAN subnets I want to be advertise on CE Router. Our Customer Router will be ru...

j44mistry by • Level 1
  • 6926 Views
  • 23 replies
  • 0 Helpful votes

pre-pend default route within BGP

We are using the neighbor default-originate command to advertise the default route into the BGP AS. We have two gateways into the service providers network and the default gateway needs to be advertised out of each, but one needs to be the primary. O...

jdriley by • Level 1
  • 10873 Views
  • 5 replies
  • 0 Helpful votes
Load more