Routing

Hello, Im using Neflow on various routers and VPNs, but I need to configure Netflwo on a router and send the Neflow data over the internet to our Neflow server.  I've created a NAT our our ASA to accept traffic on a public IP and NAT to the inside IP...

what's the username & password when i connect device from cisco network assistant?http://i200.photobucket.com/albums/aa273/wallfire02/Capture_zpsa8f5fd2b.jpg

I'm in the process of installing four Cisco 4451-X routers and see that the object-group network command is missing?! There is an object-group security but no network.Will this be coming back or am I missing something?

HelloWe try to replace our 7204vxr NPE-G2 with some ASR1002-X with 4GB of memory.Everything looks good, vrrp is working, bgp internal is also working.But as soon as we enable one upstream with full tables, the router shows the following:"cef has been...

Hi Cisco Community, I have a question regarding Spanning tree tuning. We have a 3750 stack with both te interfaces towards our core (STP root). I need to tune STP so the root port will be te 2/0/1 and not Te1/0/1 (all ports have default config).I wou...

When I put a summary address in for the interface below my routes disappear on my far eigrp neighbor.  ip summary-address eigrp 8882 0.0.0.0 0.0.0.0!router eigrp 8882 ! address-family ipv4 vrf ######  network 10.9.2.0 0.0.0.255  autonomous-system 888...

I have two routers connected to each other via an eBGP protocol. They are also connected by IPSec/GRE ,I want that IPSec/GRE link to be only used when the eBGP link breaks down.So under normal circumstances only eBGP should be used.ThanksCan someone ...

I am seeing issues with IPV6 multicast storms in my network that are fairly low volume (1-2mbit), but that are causing service disruptions due to CPU load on the switches and that the network is a Point to MultiPoint wireless network.I have about 500...

Here is my current topology: ISP Modem --------------------(fa0/0) R1 fa(0/1)-----------------S1-----------------------(fa0/0) R2   (fa 0/1)---------------S2                                    11.22.33.44       172.16.0.1      172.16.0.2             ...

Hello, I have a Cisco 2911 with all traffic currently leaving S0/0/1:0 I have hooked up cable internet to port GI0/1 and would like to have all data traffic leaving this port while all voice traffic continues to leave on S0/0/1:0I read that I would b...

I have recently changed my network of using a SG-300 (basic layer 3 switch) and put a 4507 in as the core router.  Now that I have 4 VLANS, I can not see NAS drives, Servers etc.  All the 3/x are gig fiber gbics run to the edge switches. All servers,...

Here is my topology:ISP Modem ---------------- (gig0/0) Cisco Router (gig0/1) -----------------Cisco Switch--------------------Server                                       60.70.80.90             172.16.0.1                     172.16.0.2             ...

I can't get this unit to bootup no matter what I try. I have done some research already without any results. Does anyone recognize the error and possibly let me know what is causing this crash. I think it might be hardware related.(Here is the initia...

2 uplinks are going from 2960 4 member stack to 4503 Active and Standby HSRP Core Swtich.If only one uplink is connected everything working fine.If both uplinks are connected to core, Huge packet drop is experienced, even file copying getting breaked...

Dear All,We have three sites each are connected to two MPLS connection(Full Mesh). And we have configured routing by static and default routes. and configured IP SLA for failover and PBR for specific traffic.Router on each site is 2811 Each router is...