Hi, I am new to ppp, and have so much confusion about authentication. I have read many articles and threads, but my doubt is not cleared. Unfortunately, cisco documentation is not clear on many aspects. R1 and R2 are connected back to back. I w...
Hello,This router was running fine since a few years.We had to do an electric maintenance yesterday morning and the router had to be electrically shutdown.When rebooted it started crashing systematically after booting.We've tried to remove linecards,...
Hi to all. Please help. I had this topology:Problems:1. Can`t connect from WAN to IP=X by nating rule to IP=C (NLB MS)2. Can`t create NAT rule from ISP=2 IP=Y to IP=C, telling you have NAT rule form ISP#1I thought that have some miss rules in acl lis...
Hi,I've labed l2TPv2 over a WAN connection and it seems to work fine. So far I have only configured one VLAN to traverse the L2TPv3 tunnel. There are a couple of VLANs that I would like to send across the WAN. Could I configure several L2TPv3 tunnels...
Dear all, Wonder if anyone encounter same situation of me. I build a Dual Hub Dual DMVPN with OSPF and I observed that the ospf hello packet are not arriving hub from spoke. Thus my ospf neighbor periodically up/down while the timer excee...
I updated the firmware on my rv220w router to the latest 1.04.17. I am now getting the following errer every 3 to 15 minutes. "PLATFORM [System] /pfrm2.0/bin/bwLimitConfig /tmp/system.db 18 dot11STA 8 failed. status=-1". what do...
Hello,I am new here so thanks in advance for any help.I recently purchased a 2921 to replace an aging router.We will using this router specifically for T1 data connections only. I am maxing this router out with T1 WIC CSU/DSU cards.I have 4- VWIC3-4M...
Hi,We have a setup like the following:e1------e2| \ / || \ / || / \ || / \ || / \ |c1 c2The scenario has the following features:iBGP full mesh between router loopbacksCollapsed core/distribution designEd...
We are currently migrating to a new platform, which all of our users will be on TCP/IP. Though most of our users are converting from X.25 to IP, some users won't be ready to convert from X.25 prior to the migration. We will be using a router to con...
Hy,I'm searching the details of wiring diagrams for the CAB-SS-X21 MT and FC.To make manufacture an extansion.My provider proposes only 3 meters. I'd like to make manufacture an extansion to put between the two serial cables.For that, I need to know ...
I have my Cisco IP Phone 192.168.195.241 connected to my router 192.168.195.246 with cisco switch in between, but I get drops at fixed regular intervals. Sending 100, 100-byte ICMP Echos to 192.168.195.241, timeout is 2 seconds:!!!!!.!!!!!!!!!!.!!!!...
hi,Trying to find out the best way to advertise routes based on ip-route source.R1 - ISP_A-neighbor ISP_A-neighbor R3 only advertise 0/0 route to R3R2 - ISP_B-neighbor ISP_B-neighbor R3only advertise 0/0 route to R3R3 - inside network-neighbor R1adve...
Hi,I am trying to run a capture on one of my ASR 1002 routers, however the EPC monitor capture command is not available.Please can someone provide some insight on how i can either resolve this or an alternative method. I am not on site to make any ph...
Good day to all!I have faced with a problem when I tryed to use route-maps and dynamic PAT (overload) on ASR1002 series.At the moment there are:2x ASR 1002Cisco IOS Software, IOS-XE Software (PPC_LINUX_IOSD-ADVENTERPRISEK9-M), Version 15.3(2)S1, RELE...
