Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Don't miss this Cisco Catalyst 8000 offer

 
Labels

Forum Posts

Finding accurate answers to your questions and issues is always gratifying, but what if these answers are shared globally across different languages? The Cisco Community team has been working on a proof of concept (PoC) to take Accepted Solutions in...

translator.png Asolution.png htlm-source.png insertcode(1).png
Kelli Glass by Community Manager
  • 10257 Views
  • 7 replies
  • 16 Helpful votes

HiI am planning to deploye the fwsm with all this complexity anyone tell me please this type of senario work or not means traffic will move from msfc to the core.. Is this right to create another svi int2 on msfc to move traffic from msfc to core-swi...

mca.ahsan by Level 1
  • 935 Views
  • 5 replies
  • 0 Helpful votes

Hi everybodyThis is a 3750X with ip services.I spend already some time researching and still nothing.This is my issue:I have this route that exists in the routing table learned via BGP but is not redistributed into OSPF!!!VAN-DMZ-SW#show ip route vrf...

ewaizel by Level 1
  • 1201 Views
  • 7 replies
  • 0 Helpful votes

Hi All,Trying to connect 2 switches together (both 2960G 8 ports). I have an SFP in each (GLC-LH-SM). They are connecting over SingleMode Fibre using the correct cabling. The fibre cores have been tested and are all ok also.I can't get no Layer 1 con...

GRANT3779 by Spotlight
  • 427 Views
  • 3 replies
  • 0 Helpful votes

can i do this similiar to spanning tree?  i know i have to have 2 HSRP capabale devices. only reason i ask is because i had an issue yesterday morning where i had to take down our L3 switch with all of our routes.  i want to slowly convert my network...

HiI've got a PBR configured in a interface Tunnel (with NHRP) that's not matching all the traffic coming from spokes...Trafic comes from networks 10.0.0.0/16 10.1.0.0/16 10.2.0.0/16. Enters the tunnel, enters a VRF and with the PBR we split those net...

I need to change an ip address and route in remote, because this is the only access to the router I will loose connectivity.I thought it was possible to put a file in flash and configure it from there, how should it be done, is there somewhere an exp...

pbogaerts by Level 1
  • 4899 Views
  • 4 replies
  • 0 Helpful votes

Hello,My ASA 5510 is configured with a single PUBLICIP1 on the outside interface. All internal hosts 192.168.0.x are behind the ASA firewall and NATed to PUBLICIP1 including a few site-to-site VPN tunnels. This is also true for DMZ. Now, I would like...

What happens if i implement a sercice policy on a main interface and on a subinterface? int gi 0/0/0service-policy input TEST1int gi 0/0/0.501service-policy input TEST2policy-map TEST1 class class-default    set dscp efpolicy-map TEST" class class-de...

Can someone point me to clear documentation on REP interaction with QoS? I can configure all normal QoS commands on a REP enabled segment port, but have read online that "REP doesn't pass QoS". This would seem to be a very severe limitation. Any addi...

steeda by Level 1
  • 424 Views
  • 2 replies
  • 0 Helpful votes

Dear All:        I have got a Cisco router 2811, IOS version is:        c2800nm-advipservicesk9-mz.124-24.T1       But when I need to configure IPv6 netflow, the router can't get this command:       ipv6 flow-XXXXXXXXXXX     For Example: ipv6 flow-ex...

vassiliev by Level 1
  • 265 Views
  • 0 replies
  • 0 Helpful votes

i´m not able to test at the moment.what does this command do policy-map TESTclass TESTset ip dscp efclass-map match-all TEST match access-group name TESTip access-list extended TESTthe ACL doesn´t have an entry. does the ACL hit every traffic meaning...

Hello,I'm hoping you guys might be able to help me out.  I'm trying to set up an IPSec tunnel between 2 3845 routers that each sit in a private LAN behind an ADSL modem.  Each modem does have a static public IP address from the ISP.Thus:Cisco 3845-1 ...

Hi community,In Cisco, we can support both BFD Hello and demand mode. But I don't know how to configure to select one of this mode. For example, if I want to configure my Cisco router to run in Demand mode, how can I do? In the document, it only guid...

minh_hieu by Level 1
  • 598 Views
  • 0 replies
  • 0 Helpful votes

Hi All,we are facing issue for unstability of EIGRP neighbor with ISP router.Both router are connected via 3750 switch.There is no misconfiguration or physical media issue.I found the SDM template on the middle switch is desktop default, does this wi...