while running 'aggregate-address x.x.0.0/17 summary-only' command on ASR 9k router from python code as part BGP routing protocol. It's throwing response 'aggregate-address x.x.0$' and the BGP configuration is not done successfully.Can you share input...
Forum Posts
Resolved! How to get logs in ASR 9k
Hi,Can you please let me know that how we can check the BGP, sub-interface and VRF logs in ASR 9k router.Also where the logs gets stored and how can these logs can be copied to remote location.Thanks in advance.
TOC-BP-SWa#sh ip bgp neighbors 10.14.0.3 advertised-routesBGP table version is 1674320, local router ID is 10.14.0.1Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, S StaleOrigin codes: i - IGP, e - EGP, ? ...
Hi guys. I've just installed card C6800-32P10G in my 6506 with 2T supervisor: But I noticed, that only L2 traffic could be operated via this card and any L3 traffic couldn't. I made a lab enviroment: I connected a PC(10.52.201.201/24) directly to th...
Hey guys, Could anyone explain the difference between autoroute and forwarding adjacency, please? and what would be the use case for both?
Resolved! [ncs540] Please explain IPSLA
Hello, I'm curious about the technology of ipsla Please refer to the config below and explain it.configure terminal !ipslarespondertwamp-light test-session 3local-ip 198.18.57.84 local-port 13000 remote-ip 198.18.57.254 remote-port 13001 vrf default!...
Dear Cisco Community ,Hope everyone is well. Reaching out to ask your expertise with regards to this scenario.Two sites: Main branch and Remote branch. Two firewall in the environment, FW01 serving as default route for all LAN traffic (VPN tunnel cl...
Resolved! [ncs540] Please explain slow-tracking
I wonder what kind of slow-tracking technology is used by ncs540 Below is an example. Please refer to it when explainingconfigure terminal !ptpservo-slow-tracking 16!show configuration!commit
I have the following network (see attachment):Router's interfaces:Interface IP-Address OK? Method Status ProtocolGigabitEthernet0 unassigned YES NVRAM administratively down downFastEthernet0 ...
Hi,I have configured a small topology with 2 x RTRs and 2 x SWs and have 2 ISPs and have configured HSRP for failover. I have connected ISP 1 to RTR 1 and ISP 2 to RTR 2, now vlan 10(ISP 1) that is for ISP 1 is working perfectly fine in SW 1 while no...
This is my current setup (see attachment): There are 3 VLANs: VLAN 1 (management) 192.168.0.0/24 where all network devices live (router, AD server, switches) VLAN 10 192.168.1.0/24 : where PC1 and PC2 live VLAN 20 192.168.2.0/24 : where PC3 an...
Resolved! Desactivar BGP address family
hola comunidad, aplique por error el siguiente comando en mi ASR1002 (Cisco IOS XE Software, Version 16.05.01b) "neighbor 10.99.2.18 activate" y me cambio la vista en la saluda del comando "sh run", de tal manera que no muesta los prefix-list ni los ...
Resolved! License of C8300
Hi, I'm preparing C8300-1N1S-6T BOM to replace 3954-VSEC-K9 router. It has Cisco 3945E Voice Sec Bundle, PVDM3-64, UC&SEC Lic,FL-CUBE10 I'm bit confused as how to VSEC license for C8300 router? Do i need to add DNA-P-T2-A-3Y license of L-DNA-C8300 l...
Hello.If there exists no explicitly configured EIGRP router-ID, and also there exists no loopback interface...... will the device's EIGRP router-ID advertised to a neighbor instantly change to the loopback interface, or must some reset command (or re...
Hi everyone, I'm experiencing a very frustrating problem with route redistribution from eBGP into OSPF. Consider the below diagram. The goal is to route traffic as directly as possible to the Azure networks 10.24.0.0/16 and 10.25.0.0/16. This was all...
