Finding accurate answers to your questions and issues is always gratifying, but what if these answers are shared globally across different languages? The Cisco Community team has been working on a proof of concept (PoC) to take Accepted Solutions in...
Hi,I work in a large network where we have 60 sites linked up over a radio SDH network. We are thinking about buying a fixed line (dark fibre) between two of the key sites and bypassing the radio network. Layer 2 ethernet will be presented by the c...
Hi All.We've got a 1841 router with dual-WAN connection, one is Cable and it goes to Fa0/0, another one is ADSL2+ and it goes to WIC-ADSL card.I'm trying to configure a load-balancing and failover using per-packet or per-destination connection.I can ...
Hi team,I have a Cisco 3925 router running IOS 15.2 I am trying to configure IP SLA on it. The configuration is supposed to be what is pasted below. but the CLI is rejecting the commands. Can anyone please help?Its taking oly the "ip sla responder" c...
20 permit ip host 71.72.73.74 61.62.63.64 0.0.0.15IP used here is just for an example. i have seen this when i put sh access-list command in a router. can someone please describe the meaning of this line.
Hi,I was doing some testing & came across a picular issue. 3 nos. of routers connected to each are running EIGRP. I create 5 prefix-list for some networks.I call these prefix-list in route-map. The syntax of the same is given below.Router# show route...
Hi,I have a couple of 887VA routers under my management. I noticed that none of them is allowing for bigger than 10 Mbit/s transfers via WAN link despite being synced with ie 15 Mbit/s or 17 Mbits/s.I tried different IOS images and ADSL firmwares but...
Hi,I have got a cisco 1841 router. I need to do many nat. I have got a lots of virtual interface on this router. How many nat inside and outside does it supports ? Can I do more than one nat insdie and outside in different virual interfaces on the sa...
Hi everyone!I have 4 subinterfaces on FastEthernet 0/0, listed below.How can I make such that each of them has a DHCP server enabled?!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!interface FastEthernet0/0.4 description VLAN20-Management e...
Hi,We are facing the issue,In Local LAN segment, we normally using 2 Public IP pool address for PAt ( ISP1 & ISP2),In normal scenario, all works fine, ISP1 PATIP mapped address take path of ISP1 router --internetISP2 PATIP mapped address take path of...
Hi,We currently run OSPF across our core (7 POPs), to redistribute all static+connected subnets - Works fine when customers only have subnets directly connected, or we statically route additional subnet to them (Our "Internal" OSPF redistributes thes...
HelloDo you know what is the diffrence between SPA-2XOC3-ATM (2-port OC-3c/STM-1 ATM Shared Port Adapter) and SPA-2XOC3-POS (2-port OC3/STM1 POS Shared Port Adapters)?
Dear All,We are configuring the below event manager config on the cisco routerevent manager session cli username "<name>"event manager applet XYZ event track 1 state down action 1.1 cli command "enable" action 1.2 cli command "config t" action 1.3 cl...
I read in book (MPLS fundamentals) in section (Packet Forwarding in an MPLS VPN Network):- How does the egress PE router know which VRF the packet belongs to? This information is not in the IP header, and it cannot be derived from the IGP label, beca...
Hoping someone can either tell me how to do this or why it isn't possible.Using Cisco 1811W with IOS 15.1(4)M5. FE0 and FE1 are connected to the internet via Billion ADSL2+ modems operating in bridged mode. Both lines are similar so I'll only discu...
Hi!R1#show ip prefix-list detail p-filter-in | i seq 160 seq 160 permit 170.180.190.0/20 le 24 (hit count: 0, refcount: 4)R1#Could anyone tell what is the meaning of "refcount" - variable counter in a prefix-list ?? Hit count is obvious what does...
.png "Hall of Fame"){kind=icon}
