Finding accurate answers to your questions and issues is always gratifying, but what if these answers are shared globally across different languages? The Cisco Community team has been working on a proof of concept (PoC) to take Accepted Solutions in...
Good Morning, We're having troubles redistributing routes learned over iBGP VPNv4 from a PE to the VRF Customer1 of a connected CE. The PE (XR3) receives the IPv4 route 10.2.0.0/24 over iBGP VPNv4 from the RR (2011::1):OS is Cisco IOS XR.RP/0/RP0/CP...
I have a network with multiple (5) ISR4321s in an ELAN. I have set up service routing on all of these routers for the purposes of running different topologies and stacking different networks on the equipment. For example, some of the service instan...
Hi folks! I have a Cisco RV320 that I want to use for assigning IPs both statically and via DHCP.The router has two wi-fi access points and a PC in three ports, assigned static IPs. I want to add an Arlo camera system in a fourth port that requires D...
OSPF neighborship between Cisco Core Switch and Palo Alto Firewall is flapping in point to point network. Due to which we have change network type at Palo Alto end as a broadcast now ospf neighborship is stable but not able to reach few IP address of...
Hi all, need your guidance.., my CCIE Routing and Switching Lab exam is expiring in mid Feb 2023. What's the best way to get recertified within this time frame? Your guidance is appreciated in advance. Thank you, Jit
Issue resolved.
Hello,I would like a specific subnet to see a route in the routing table where other subnets are not able to see it. For example, let's say I want 10.1.1.0/24 to be able to route to 192.168.1.0 255.255.255.0 via next hop 1, but all other networks us...
Can someone please help me out with this concept?The global config command ip cef enables CEF on R2To disable CEF on an interface i run the command no ip route-cache cefOn the above lab I disabled CEF on both interfaces of R2, yet the packet is route...
We have a global MPLS network that I would like to backup utilizing VPN tunnels on our Firepower appliances. Our MPLS network utilizes BGP for routing. When I try to configure a full mesh VPN network in Firepower Management Center and deploy it to th...
Hello Team,I have recently passed Cisco 350-401ENCOR & 300-410ENARSIDetail350-401ENCOR ---passed on 20th-nov300-410ENARSI ---passed on 30nov-22In certmetric exam metric I can see both exams.However on Cert status I can only see CCNP is re-certified C...
Hello,we have ISR4431/K9, isr4400-universalk9.03.16.04b.S.155-3.S4b-ext.SPA.binWe have configured Service-policy output on the Port-Channel interface.But command sh policy-map interface po 1 shows:Service policy internet-limit is in suspended modeWha...
Hello,I have issue with below topology, currently CSR router receiving routes from XR-4 using vpnv4 neigh, but CSR not sending routes to XR-4,XE-5#sh bgp vpnv4 un all neighbors 4.4.4.4 advertised-routeTotal number of prefixes 0XE-5#==================...
I have my switches connected as follows. But I've seen these logs (both on port-channels and interfaces) on both core and access. Logs CORE *Nov 29 15:41:05.226: %SW_MATM-4-MACFLAP_NOTIF: Host 827d.bb89.a409 in vlan 82 is flapping between port...
Good morning Checking an ACI leaf switch I found these static routes ip route 10.10.0.0/16 0.0.0.0 200 (gateway 0.0.0.0 ?)ip route 10.10.0.0/16 10.1.0.1 210 Checking the routing table, it's been considered only the route number 2 (distance 210) 1...
Im pretty sure this is the right area to post my question. The question is "Q3: change the configuration to make all the computers communicate with each other.". Right now Im able to communicate between two computers that are on the same VLAN but Im ...
