I have router 7604 and when i apply police-map to interface port-channelto limit the rate but when i see the monitor the port didn't drop the packet when reach the maximum ??port-channel with 4 interfaces Gigpolicy map with 2.8 Gig
Forum Posts
Peace upon you brigadiers !Does it make sense my question?A host uses the address/mask combination of 192.168.32.99 255.255.128.0. If all subnets of the same class A, B, or C network use that same mask, how many bits are used for the subnet part of t...
Resolved! The use of VRF Lite
Hello, everyone! I have a quick question about VRF Lite.So I understand that VRF is a technology which allows the router to build multiple virtual routing tables which divide the network on L3 with each VRF table being isolated from the other VRF tab...
i need to install custom config on a ISR 110-4g router, need to erase the vedge config. i dont have a Vmanage dashboard, need to make it stand alone device with custom config. Tried the reset button with no result. need help.
Hello, We have two firewalls (configured in failover cluster) which are each connected to a single C9500 inside switch.Both switches are interconnected (L2 trunk). We have one ASR1001X router running 15.5(3). It has a 4x1GE portchannel to one of thes...
Resolved! Opinion choice cisco
Hello, I allow myself to write to you because we have in the company where I work routers that we would like to change to cisco products. In particular, we saw the cisco n9k-c93180yc-fx what do you think ? We need a router that supports at least tw...
Resolved! VRF passthru
Im not sure this is even possible and if it is how to configure it but take the following setup... PE - - CE 4500 - - LAB 3750. Lab wants to create a VRF that will passthru the CE and land on the LAB3750 The WAN circuit terminates on the 4500 and typ...
Hello,I'm trying to do Vpn site to site failover on both RV042G , please find attached the architecture.Could you please give me a guide or video to help me ? Thank youSmart Link Backup RV042G @vpn
Resolved! OSPF DR/BDR election with VLANs
Hello, Could anyone explain how DR and BDR are supposed to be elected in this environment? I configured OSPF for all of the routers, and provided each router the networks adjacent to its interfaces. But I did not change any priorities so I could see ...
Hello.We have the following setup: ISP A provides BGP with a full view.One layer of our security model relies on routes, we receive from ISP. To be more precise: on the absence of such routes. We block certain ASNs by adding them into the as-path wit...
When I'm connecting the router to laptop, the port is showing up. But when I'm connecting the router to 100Mbps media converter, the port is showing down
I bought this switch to use it at home to manage the many home automation devices.When I first accessed it there was no way to enter express setup modeNot being able to enter that mode, I then looked for guides on how to remedy the problem but trying...
Resolved! OSPF showing only 1 multilayer
I used below ospf routing (multi layer ports are no shutdown state)roue#multi-1int gig1/0/1ip address 172.1.6.129 255.255.255.252no shexitdo wr#multi-2int gig1/0/1ip address 172.1.6.133 255.255.255.252no shexitdo wr#routerint gig0/0ip address 172.1.6...
Hello community. I have a Cisco 1941 router that I need help with password recovery. Here is part of the boot screen when connected to terminal via console port: Readonly ROMMON initializedPASSWORD RECOVERY FUNCTIONALITY IS DISABLED I searched on int...
Please help, what configuration is required so that I am able to ping from R3's 192.168.0.2 to R2's interface Gi1 that is running in VRF INET with IP address 192.168.1.1/30 Thanks in advanced.
