Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Webinar

 
Labels

Forum Posts

Resolved! DMVPN Issues

We have been having DMVPN issues since we started implementing it. The build was originally set up with EIGRP. We were having alot of problems - missing routes, neighbors going up and down and we thought it might be easier to change all the remote ro...

Hi All,I have a Router that connects to a IP WAN. Its a over subscribed link by a fair bit.  This router has a 4mbit link to the WAN while the sum of other sites are well over 20mbit.I have configured HQF on the outbound of the router and bumped up t...

We have 4 sites that are all connected together and are all routable across the LAN. We will be adding internet to all 4 sites and need to have redundancy. We will be using a default route for each site. What would be the best way to configure redund...

faze1sari by Level 1
  • 1769 Views
  • 3 replies
  • 0 Helpful votes

Hello, we have strange situation on some 2911 and 3945 routers when configuring nat. For example there are no "nat inside" statements in the configuration of 2911 router, but anyway i see this translation in the "show ip nat trans *" output:Pro Insid...

Hi, we have private line between our data centers (they are 1500 miles apart). on one end it is connected to nexus switch and on other end it is connected to 6500 switch. nexus switch interface that connects to this private line shows as DOWN while 6...

gavin han by Level 1
  • 720 Views
  • 3 replies
  • 0 Helpful votes

Hi,I work in a large network where we have 60 sites linked up over a radio SDH network.  We are thinking about buying a fixed line (dark fibre) between two of the key sites and bypassing the radio network.  Layer 2 ethernet will be presented by the c...

ohareka70 by Level 3
  • 620 Views
  • 2 replies
  • 0 Helpful votes

Hi All.We've got a 1841 router with dual-WAN connection, one is Cable and it goes to Fa0/0, another one is ADSL2+ and it goes to WIC-ADSL card.I'm trying to configure a load-balancing and failover using per-packet or per-destination connection.I can ...

Hi team,I have a Cisco 3925 router running IOS 15.2 I am trying to configure IP SLA on it. The configuration is supposed to be what is pasted below. but the CLI is rejecting the commands. Can anyone please help?Its taking oly the "ip sla responder" c...

20 permit ip host 71.72.73.74 61.62.63.64 0.0.0.15IP used here is just for an example. i have seen this when i put sh access-list command in a router. can someone please describe the meaning of this line.

skmparvez by Level 1
  • 703 Views
  • 5 replies
  • 0 Helpful votes

Hi,I was doing some testing & came across a picular issue. 3 nos. of routers connected to each are running EIGRP. I create 5 prefix-list for some networks.I call these prefix-list in route-map. The syntax of the same is given below.Router# show route...

Hi,I have a couple of 887VA routers under my management. I noticed that none of them is allowing for bigger than 10 Mbit/s transfers via WAN link despite being synced with ie 15 Mbit/s or 17 Mbits/s.I tried different IOS images and ADSL firmwares but...

Hi,I have got a cisco 1841 router. I need to do many nat. I have got a lots of virtual interface on this router. How many nat inside and outside does it supports ? Can I do more than one nat insdie and outside in different virual interfaces on the sa...

Hi everyone!I have 4 subinterfaces on FastEthernet 0/0, listed below.How can I make such that each of them has a DHCP server enabled?!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!interface FastEthernet0/0.4 description VLAN20-Management e...

Hi,We are facing the issue,In Local LAN segment, we normally using 2 Public IP pool address for PAt ( ISP1 & ISP2),In normal scenario, all works fine, ISP1 PATIP mapped address take path of ISP1 router --internetISP2 PATIP mapped address take path of...