Finding accurate answers to your questions and issues is always gratifying, but what if these answers are shared globally across different languages? The Cisco Community team has been working on a proof of concept (PoC) to take Accepted Solutions in...
Dears,I have Cisco 1841 Router with no WIC cards and USB.Image is ipbase and on the flash. When it boots it gives the error and hangs - As suggested I changed the register value to 0x2142 but no change happened.Following are the capture from the rou...
I have not worked on the new VWIC cards lately. I would like to know how I can configure the serial IP address like we used to do in the older T1 DSU WIC cards. I do not see any interface that shows as serial. I have configured the controller as a T1...
We have 3 or 4 older sites that connect back to our central site using ATM over 2 T1s. This connection is for both voice and data. Equipment is a 3640 router and 8510 switch. These are our last sites on ATM, and we'd like to move them away from ATM a...
Hello,We have a network with metroethernet services. We are using Q-inQ tunneling to implement P2P services to interconnect two facilities of a same institution. We are growing and now we have a ring topology. Until now we had disabled the MAC learn...
Hi All;Is it possible to be able to control the download traffic on the DSL router 887 Security Bundled, so I can give 30% of the downloaded bandwidth for the voice and 70% of the downloaded bandwidth for the data? So maximum data to take 70% of the ...
Hi there,I ve got a problem with 2 c3700 running IOS 12.3(4)T4.. Firstly the routing table couldnt be accepted (read the subnet thing that goes on when the broadcasts are sent) and i had to #no validate-update-source but still i have no ping replies...
Using IOS image c2900-universalk9_npe-mz.SPA.151-4.M.bin to perform NAT with SDP, it works perfectly with RFC1918 address scope, but sends the originating ip address instead of the global outside address when the LAN is assigned a public range addres...
Good Afternoon Everyone,I set up a scenario in a lab with the routing protocol ripv2, and I realized that the rip does not disclose the subnets of the loopbacks. whereas the second version works withVLSM, why he would be releasing a full class?In Ann...
Hello,Simple question, if I create a trunk group (example trk6) on a core switch do I name the trunk group number on the edge switch I am configuring?Example I have a 5406zl I've created a number of trunk groups, do the trunk numbers need to be the s...
i have 2 routersr1---fa 0/0---ip address ----192.168.1.1r2--fa 0/1---ip address------192.168.2.1i have connected them by fast ethernet .can i ping them?if yes then how? if no then why???
Can't seem to get rid of extra characters in banners for either, login, motd or exec. Do i understand the cmd properly: that the result will be the deliminiter at the start AND end of the text ? Why can't I get rid of the extra "C" char at the star...
Please, I need a help on PFR routing.I am using a 2900 (15.2(2)T) and I am getting these messages:PFR PIRO: No parent found, network 10.10.2.1 interface Tunnel1PFR PIRO: No parent found, network 10.10.2.1/32OER BR ACTIVE PROBE: Parent route not found...
All,Where does a FR switch sit in relation to a provider's network? Does it sit on the edge or behind a router? If it sits on the edge, how do I keep the customers in a VRF? Do I only map from the customers perspective to the PE router?Example:PE1 --...
Hello, I was doing a PPTP VPN in a CISCO 3800, and it wasn't working...not even the debug for pptp isakmp gave any error...it just failed connecting to the VPN concentrator (the cisco 3800). At frist I thought....well connectivity problems...some fir...
Hi everyone,Is it possible to upgrade a supervisor 4 or 5 to a sup 6 on a Cisco 4507R, in a redundant supervisor environment? My goal is to ensure minimal or no down-time, and to also have the config synchronize between the old and the new sup, so th...
.png "Hall of Fame"){kind=icon}
