Routing

3G router C819H access internet fail

Dear all,I have a SIM card which can support 3G internet access, that is I can use notebook to access internet via 3GNotebook(WiFi) -->WiFi (Mobile phone) 3G --> internet. --- (Remark: username and password is not require)When I use this sim card to...

OSPF ASA 5520 in failover mode

Okay guys so I'm sort of in a predicament. I currently have a set of firewalls in active standby configuration running an ospf process injecting a default route into the rest of my network.I noticed when i was testing the failover that the asa's do n...

Resolved! Removing static route Get error %No matching route to delete

I am trying to remove a static route I added:-------------------------------------------------------------------------------------------------r2#show ip routeCodes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP...

Resolved! N5k and 3560 E

Attached is the topology,3560E at distribution layer (Layer VLANs- Existing connection)N5k at access layer (new connection),We have a problem of network loop and packet loss.Log from 3560E switch 1: May 16 07:58:13.668: %SW_MATM-4-MACFLAP_NOTIF: Host...

Nexus 5596U EIGRP route preference

Hello. I have a customer with a primary datacenter and DR datacenter, that has a P2P 100Mbps link connection between them. At the primary Datacenter there will be a Nexus 5596U with a L3 card running EIGRP, it will have three connections, one nothbo...

Automatic redistribution of EIGRP routes into iBGP

I have an iBGP session between two routers and and at the same time I am running EIGRP between these two and two other routers.R1 (.173)-->iBGP-->R2 (.174)R1(.237)-->EIGRP-->R2 (.238)R1(.233)-->EIGRP-->R3(.234)R1(.241)-->EIGRP-->R4 (.242)R2(.245)-->E...

"max-reserved-bandwidth" alternative command

The 7606-S router running IOS Release 12.2SR do not accept "max-reserved-bandwidth" command in SIP-8XCHT1/E1 interfaces. The Legacy QoS CLI Commands Deprecation document (http://www.cisco.com/en/US/partner/docs/ios/qos/configuration/guide/legacy_qos_...

STATIC NAT Problem on IOS 15.x

Few are the issues that I am facing on IOS Version 15 and Cisco 1941 Router , this router is currently in production on clients.•1. I do PAT on router interface , and it has public IP on it , when I send request to Internet via Browser from LAN...

Resolved! Frame Relay; Multilink and Point-to-point link

Hello Everyone,What are the use of Frame-Relay's Multipoint and Point-to-point? because even if I don't configure any of this two, routers connected to a frame-relay cloud can still PING w/ each other. Does these two sub-interfaces (multipoint & poin...

SMTP conversation interupted

We receive our mail through our ISP. However some of the mail is stuck in their queue with the following error message "status=deferred (conversation with x.x.x.x timed out while sending RCPT TO. this is only for some users though and not all. I have...

can i have two redist statements in ospf. i need to redistribute both static and connected

can i have two redistribute statements in ospf. i need to redistribute both static and connected

IP OSPF NETWORK POINT TO POINT ISSUE

HI ALLI have a 7609s and 7206 vxr and have configured a gig port as routed and ospf enabled but when both of them are without the above command or both of them have this ip ospf network point to point enabled they get amazingly packet drops but when ...

Resolved! simultaneous dual wan access with nat

Hi,I have a 1841 router with two wan access from two different ISP:1: throught dialer with fixed ip obtained from dhcp - ATM interface2: thought fastethernet 0/1 with fixed ip and a specific gateway - can be use for Internet traffic if dialer is down...

Resolved! Router won't route (NAT)

I have a router that won't route. I am swapping out one router for another, bringing up different legs of the network one at a time. The configuration is similar between the two routers.I believe that I have tracked this down to the nat configuration...