Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Webinar

 
Labels

Forum Posts

hi,I have seen this config on the internet and wondering is this correct ?say for example we have two company A and B. Company A is running ospf all in the  backone area 0Company B is also running ospf in backbone area 0now there is a  link from comp...

Hello, I am facing a strange problem. I have delpoyed a network using 5 routers R1 ----> R2 ---> R3 ---->R4 --> R5R1 is conencted to R2 using POS STM1R2 is connected to R3 using GigER3 us connecred to R4 using GRE Tunnel over internetR4 is connected ...

Hey guys,I am trying to set up an 887 to use fe0 as a WAN port to connect to another router that was provided preconfigured by my ISP (and i have no access to change settings on it)i am able to connect to the one20 router (from the ISP) and out to th...

xa-mont72 by Level 1
  • 5842 Views
  • 11 replies
  • 0 Helpful votes

I have a problem XOT.Xot - CCL when configuring the connection was fine.However, CCL was down for 2 weeks.CCL operate after the connection has not been ordered XoT.CCL has a serial port connection, the router did not came out.Router that is connected...

Hi All,I have a Cisco 1841 router that is connected to a switch. I have WAN/LAN configured on the router and the switch is handing out internal IP's.The issus that none of the client machines can access the Internet. From within the router console, I...

I have two Cisco 3560x switches running IPBase on different sites joined by a 1gbps connection with routed ports. I have video data totalling 80mbps in site A that is crucial to arrive at Site B regardless of any other traffic on the network.What I w...

Hi,I'm implementing a multi site network and intend to use OSPF to do it. The links between each site at either 100mbps fibre or 1gbps My question is, is this better to be done with switches (3560x with IP Base) or routers (2921)? What are the main p...

helloi've got a problem with vdsl over pppoe. i've got a cisco 887VA and now want to connect to my ips with the credentials they gave me.the cd-led (carrier-detect) is constantly flashing, means i've got a connection to the isp. but the ppp doesn't c...

Good day all, I don’t know how to setup my securecrt to let me start multiple TAPS  Sessions through my serial cable (I have no Ethernet connection to my  access server just octal cable which is useing COM3) Is it possible to open multiple console se...

BGP65111 by Level 1
  • 1193 Views
  • 4 replies
  • 0 Helpful votes

Good Morning,I have a remote site that still utilizes a single T1 connection to me.  For multiple reasons we had to scrap the old T1 and have a new one put in.  The old T1 resided on a T3 as channel 25.  The new T1 is a standlone point to point.  I r...

joeisbell by Level 1
  • 1293 Views
  • 5 replies
  • 0 Helpful votes

HiIP SLA works great.  If Provider 1 is down then all traffic is shifted to Provider 2 but administrator is not aware if the link is down.Our NMS monitors interfaces and hence if the interface is up and service behind it is down it cannot reflect it....

Hi Guys,(Apologies if this is too off-topic for the cisco list)Have 3 POPs A,B+C (A connected to B via 200Mb Eth, B connected to C via 250Mb Eth), all POPs are 7200's with 2960's and 3560'sLatency:A -> B,  2 - 3 m/sec (No packet loss, minimal jitter)...

Review Cisco Networking for a $25 gift card