Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Webinar

 
Labels

Forum Posts

I've been trying for a while to get a router working between two sites and am requesting some assistance.Router on my end has three interfaces connected:Gi0/0.100 - internal to my network - 10.138.247.235/29Gi0/0.200 - internal to my network - 10.138...

campbech1 by Level 1
  • 1076 Views
  • 1 replies
  • 0 Helpful votes

Hello Community,I am thinking of introducing a DMZ to my network.My current web servers are located behind the firewall using port forwarding. I have about 20 of them. These servers host demo products of software. They are accessed by our internal em...

imanco671 by Level 1
  • 1471 Views
  • 6 replies
  • 0 Helpful votes

folksi'm trying to upgrade an asr1001 (r1) from asr1001-universal.03.02.00.S.151-1.S.bin to  asr1001-universalk9.03.02.00.S.151-1.S.bini've put in the boot system flash asr1001-universalk9.03.02.00.S.151-1.S.bin command and reloaded but the box keeps...

Resolved! packets drop (QoS)

Helloto garantee a bw for oracle application i configured this in HQ (oracle server is there)class-map All-Trafficmatch anyexit!policy-map G01-Policyclass All-Traffic   shape  average 16000000 (the wan speed is 16Mbps)   service-policy outbound-Polic...

ohassairi by Level 5
  • 1112 Views
  • 1 replies
  • 0 Helpful votes

I have a 1841 router attached to 2 ISP's. Each ISPs provides different bandwithd. I want to do load balance between them, but I want to do some sort of weighted load blance, so as to assign more traffic to one ISP than the other. A kind of 70/30 (70%...

hi all,I have a l2tpv3 tunnel setup between 2 x 3845 routers. Now, there is roughly about 100-150mbps or more traffic flowing across the tunnel. Now, some large files seemed to be transferred over the link and its causing heaps of fragmentation on th...

Hi everybody,   Please can someone help me with this?   I wanted to block users in my company network from visiting social networking sites like facebook, youtube etc, I used the configuration below:   (config)# class-map match-any SOCIAL-NET(config-...

tomocisco by Level 1
  • 5147 Views
  • 5 replies
  • 0 Helpful votes

Hi, I have one switch in a small office which I have defined 2 VLANs.  One VLAN (VLAN 10) is for data and another VLAN (VLAN 20) is for voice.This small office network is connected to the headquarters network.The small office network has a DHCP serve...

Hello,is there a cisco command to check the list of incoming vlans on a catalyst 4640 or at least that will give you the same output?we're having an issue with an ethernet circuit, links are up but ping won't go through(no ACLs) and I want to see if ...

jsheriony by Level 1
  • 420 Views
  • 1 replies
  • 0 Helpful votes

I have a IPSEC tunnel setup with a vendor, not GRE and we can FTP files if they are smaller than 1394 but anything larger fails.  I thought it may be a MTUissue but I am not sure how to set an MTU on an IPSEC tunnel only.  I understand how to with a ...

I have a design question regarding configuring OSPF for two sites. Say, Napa and Sonoma. I All traffic not local to Sonoma including 0.0.0.0 needs to be routed through Napa over a private wan link.Would creating a stub area for Sonoma be the solution...

cbse120109 by Level 1
  • 4834 Views
  • 16 replies
  • 0 Helpful votes

Resolved! Creating DMZ

Hello Community,creating a DMZ on a ASA 5510 router within my environment of 3 internal subnets who have thier own firewall.I have ethernet0/0 assigned a WAN addressI have ethernet0/1 assigned a subnet 192.168.201.0I need to add ethernet0/2 a subnet ...

imanco671 by Level 1
  • 1071 Views
  • 2 replies
  • 0 Helpful votes

Resolved! NAT with 2 ISPs

Hello.We are two Organizations set in one office.We utilize one Cisco 2821 Router with etherswitch module both.Each Organization has own subnet and Organizations are separated via VLans.The question is how can we make sure that Organization #1 set to...

Hey Guys,I'm wondering if anyone out there has any good troubleshooting commands to find out if MTU issues are going on.I know I can use patth MTU, tcp adjust-mss, ip mtu reset the df bit, but i'm just wondering if there are any good show commands or...

jecker by Level 1
  • 4829 Views
  • 2 replies
  • 0 Helpful votes
Unanswered Topics
Review Cisco Networking for a $25 gift card