Hello,Is there any difficulties in upgrading ASR from 2.6 to 3.1 version? I mean is there necessary to use any additional licenses in 3.1 if router worked correct with 2.6?
Hi,i have a cat6509 that has the following module, im trying to apply my policy-map to int g1/3#show moduleMod Ports Card Type Model Serial No.--- ----- -------------------------------------- ----------------...
I have noticed on my 20 site DMVPN network that traffic shapping is not working correctly. I am using a broadband provider and have several sites on a 50 Mbps down / 10 Mbps up Link, including the Hub site. The problem that I see is when one of my h...
I want to know what is the command to check the packets processed per second on a cisco 7206 vxr with npe-g2... like on sup-720-3b we have "show platform hardware capacity" where we exactly know what is the rp and sp utilization with packets per seco...
A simple nat config with host directly connected to f0/2 with IP 30.30.30.2 is not able to ping 20.20.20.1 connected directly to f0/0...is there anything I am missing?!interface FastEthernet0/0 ip address 20.20.20.2 255.255.255.0 ip nat outside ip vi...
Hi all,Currently, our network infrastructure has area 50 and area 0. Area 50 has about 5 routers and Area 0 has about 3 routers.3 of the 5 routers in Area 50 are ABRs and all of the area0 routers are ABRs to the Area50 routers.The problem that I am ...
I have been trying to work out how to allow access to a website via https with a failover dsl solution. I have already configured the failover dsl using route-maps and a ip sla track and I now have smtp working on both public IP addresses if the one...
HI,I've looked at the RPS-2300 documentation and have a couple of questions with regard to its use.If connected to a router (2851) and the power/PSU fail the RPS-2300 unit will support the router. However when the normal power is replaced the documen...
Hi all,I am trying to configure ISDN backup for a client. The scenario is as follows:Remote branch is connected through Metro ethernet with edge router A. Routing protocol is OSPF and everything is tunneled through a GRE tunnel.I need to configure IS...
I have a hub-and-spoke multipoint frame relay network configured with EIGRP and all routers receive routes from eachother. If I ping or traceroute the IP address of a loopback on spoke R2 from spoke R3 it goes out to the hub R1, but never gets any f...
Hello All,We've implemented PBR between our main and branch offices. However, it seems to have issues - the packet losses (via ping is extremely high, the traffic gets interrupted, etc. Does anyone have any information on how to troubleshoot it?Here'...
Hi all,I am new on Cisco, and I have a 1812J, since I want to using the 256M RAM with 64CF card IOS.So now I upgrade my Cisco 32CF Card, and now I just can buy the SanDisk 4GB card.Then I am using my computer and CF Card Reader to just copy the IOS a...
I've been having random loss of WAN connectivity with this router. Somehow it gets connection back after couple hours. After looking at the log file, I see the above ping error show up every few days. Can someone tell me what this error means and ...
Hello Experts,I would like to ask you a favor. I am having a trouble finding a manual or guide on how to setup a firewall on an IP Unnumbered interface for Cisco 2900 series router. Please help.Thank you very much in advance!Our router setup is as f...
we are considering this model: CISCO887GW-GN-A-K9 but we are not very sure if it support dual wan (use both wan connections in the same time).details: we are intend to use the router to connect vpn back to HQ. remote sites have some application/sys...
