Finding accurate answers to your questions and issues is always gratifying, but what if these answers are shared globally across different languages? The Cisco Community team has been working on a proof of concept (PoC) to take Accepted Solutions in...
I have simple nat config which I need to use:ip nat pool test 40.0.0.3 40.0.0.3 netmask 255.255.255.0ip nat inside source list 1 interface GigabitEthernet0/0/1 overloadip nat inside source list 2 pool test overloadaccess-list 1 permit 10.0.0.0 0.0.25...
Hi All,I have 2 networks connected via OSPF. I need to route the connected networks to a third network via BGP.I noticed that BGP peering is established but no entry is visible on the routing table.Below is an extract of BGP config:router bgp 65200.1...
Hi, how are you :). I have one question, about router Cisco 2911, and Juniper Netscreen 25, ver 5.4. I must start IP Sec tunnel between these two devices. I must use agressive mode, I saw this in configuration document. Question, how can I use agres...
Hello I am currently having trouble translating a configuration on a serial interface from a C3900-SPE150 to a C8300-1N1S-6TThe current configuration on the C3900 on the serial interface is as follows:ip address X.X.X.X 255.255.255.252encapsulation...
Hello,I need your help - currently we have a 2921 Cisco router connected to dual ISPs using "gi0/0 & gi0/1" and we are able to connect to either ISP successfully. Once we connect gi0/2 to any device the connected switch is not able to access the in...
Hi Experts,Basic question regarding the ISIS process. If I have a default config of ISIS between simple two IOS-XR routers:In this case both level-1-2 will form neighbor relationship.RP/0/RP0/CPU0:test1#sh run router isisrouter isis ISIS-COREnet 49.0...
I am trying to configure a qsig-gf link between an Alcatel PBX and a cisco router with IOS 12.4, but I did not find any document concerning this subject. here is the show version : Cisco IOS Software, 3800 Software (C3845-ADVENTERPRISEK9-M), Version ...
On which case we can say there is high interface utilisation Either case 1 when transmit percentage is high Case 2 when Received percentage is high Or Both should high
I am tying to upgrade the ROMMON from 15.4(r3)s5 to isr4200_4300_rommon_1612_2r_SPA.pkgthe output I get when I type in: upgrade rom-monitor filename bootflash:isr4200_4300_rommon_1612_2r_SPA.pkg allChassis model ISR4331/K9 has a single rom-monitor.Up...
My PC0 to PC3 can get IP from DHCP service, but I don't understand why the same thing cannot happen on PC4 and PC5. Please explain for me, thank you!
So I've been working on my project and I've implemented vlans nad also router stick.Now I want to block connections between vlans that are not same with extended access list but something does not work..Here are the commands that I've writtenip acces...
I have recently upgraded from a 887 router to the 1100 ISR, we have a third party client that uses this router to VPN into the local network and connect to some of the services on the LAN. They use PPTP and standard windows client however since being...
Greetings,The customer has 2 BGP links towards us, separated dual homed (PE1-CE1 & PE2-CE2), who is asking why they are receiving traffic on link No.1 even they have already configured route-map to deny all routes imported from & exported to PE1. The...
Thank you for your help.Let me ask you about perpetual licenses for IOS XE 17.3.2 and later. I am using C1111X-8P and I am thinking of reporting in the CSSM offline method. The first report is due to expire in 365 days. Will the SEC and APP features,...
hi,i'll be changing an ISP/BGP peer. my question is, do i negate first the old bgp router-id or just directly configure/apply the new router-id?do i need to do a "clear ip bgp" to establish the new ISP/BGP peer?router bgp 65123 neighbor 63.21.16.4 sh...
