I'm trying to set up a static network NAT, but only when trying to communicate to a particular host. This is in a test lab at the moment.What I want to happen is that when a host on the 172.16.1.0/24 network tries to talk to 192.168.1.65 it would be ...
Dear All,I have configured a cisco router to work as a Frame Relay switch. I have two serial ports connected to 2 routers.I find these serial interface on my routers going up and down. Below are my configFR================!interface Serial0/0 no ip a...
so this is what i have....isp ---> serial port 2801 ---> security gateway -----> core switchI would like to make the 2801 transparent, can someone please tell me how to do this?
Good Day All,I have a cisco 1760 with a WIC1-ADSL card installed. I have configured it and can connect to the internet, outbound. The problem I am having is getting traffic inbound to internal servers using NAT. The provider is not blocking any of th...
does prefix-list has any limit to the number of neighbours it can be applied?? if it doesnt work after appplying to certain number.. does it relate to a bug??
We have Cisco routers with Cell modules - which work very well, however when the end-user gets involved, singal strength becomes our major troubleshooting call. The user has no way of logging into the router to run ANY commands. The blinking indicato...
We are replacing old frame relay lines that connect my companies 4 facilities with metro E so it looks like this (presumably)My cisco reseller and bellsouth told me that the cisco 3560g was a layer 3 switch and would fine for the metro (hopefully the...
Hi,I have a big doubt on how I can configure PPPoE on a C881 with FVRF. I explain a bit deeper. Our customer is migrating from a IPsec HUB and SPOKE network to a DMVPN network. There is a SPOKE location in France which should get a new C881 to join t...
I put this post (below) on www.networking-forum.com and have been researching it this afternoon but not yet found an answer.Anyone got any ideas.Hi,This has got me stumbled. I have a pretty straight forward lab. 4 Routers as follows.Router A - ASBR i...
I have 2 sites, with 2 connections between them. We are using ospf for routing.I'd like to route all traffic except one subnet over the #1 connection and just the particular subnet over the #2 connection.If the #2 connection fails I'd like that subn...
Hi experts,I'm setting up a test network and I have two routers connected together through a VPN tunnel and they are running ospf. The "spoke" router has a loopback interface with IP 10.0.2.1/24. However this route is learned by the "hub" router as a...
HiThis question came from our CSC Facebook Community.http://www.facebook.com/CiscoSupportCommunityIs there any router by CISCO that can control the bandwidth, without the computer being turned on?
I wish to have a conditional advertisement for some of the networks statements to a BGP neighbour while some are always advertised, assuming the route for that network is in the routing table. So there would be 2 groups of routes: A) Always advertise...
Hi everyone,I need 15 meters length of x.21 DB15 cables that can interface router and E1 circuit?I need the part number please?thankssam
I am trying to shape traffic from hub site to slower spokes sites. I want to stop the hub site trying to send at a greater rate than the spoke can accept. An example would be copying a 10m file from hub to spoke.I have two examples below; example 1 g...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 06-14-2025 01:24 AM | ||
| 05-15-2025 07:28 AM | ||
| 05-13-2025 03:49 AM | ||
| 05-12-2025 03:28 PM | ||
| 05-09-2025 02:25 PM |
| User | Count |
|---|---|
| 9 | |
| 5 | |
| 3 | |
| 3 | |
| 2 |
