Buy or Renew
Buy or Renew

Routing

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
Labels

Forum Posts

Start a conversation

Cisco 1721 LAN to WAN Fails

Ok,  Im new here and somewhat new  to Cisco Routers.  I have used them before, but not for an actual live  enviornment.  I happen to have the fortune of my workplace giving me a  Cisco 1721 for my personal use.  I have a WIC-1ENET card for internet  ...

Hub and Spoke Frame Relay configuration

Please i need help configuring the frame relay switch "FRS",Here is the configuration on R1, R2 and R3:R1:interface Loopback1ip address 10.1.1.1 255.255.255.0!interface Loopback2ip address 10.1.2.1 255.255.255.0!interface Loopback3ip address 10.1.3.1...

Resolved! Guidance on redundancy solution

Dear All,We want to implement redundancy for our  LAN-to-WAN connectivity. There are 2  redundant L3 swithches running  HSRP connected to the LAN, and there is a single WAN router(7206 VXR,  with NPE-G1). The WAN router is connected only one L3 switc...

shree_nav by • Level 1
  • 863 Views
  • 2 replies
  • 0 Helpful votes

Resolved! Cisco 7204vxr NPE G2 + VSA

Hello Experts,I am running into issues with high CPU ( 90-95% ) on Cisco 7204 vxr with NPE G 1 ( 1gb dram ) , The router has around 100 GRE tunnels ( no ipsec protection ) , and there is constant 100 mbps traffic inbound & outbound , all through the ...

InterVLAN routing

Hi all,I got a little problem when configuring a switch Cisco Catalyst 3750. Maybe, it is a kind of easy for you guys, but I couldn't do it. So, I'm asking from you.Here is my problem. There are two vlans on the switch. Vlan 1 is connected to interne...

enkhbat.n by • Level 1
  • 876 Views
  • 4 replies
  • 0 Helpful votes

I cannot Click on "Additiinal Task" tab on SDM, to add DNS entries ?

I have 1841 router, SDM is installed but FA 0/0 is connected to ISP modem, and FA 0/1 is connected to intern/w through a linksys switch, given ip address as per the interfacesInterface                        IP-Address      OK? Method           Statu...

Resolved! BGP and OSPF Load Balance

Dear All, I have an odd case please see the diagram link below, i need reach from R-C01 (192.168.253.0/24) to 192.168.90.0/24 load balance or load  sharing via R-BH-01 and RR01 is it posible ? how to  configure it?

morse_d3d by • Level 1
  • 1284 Views
  • 2 replies
  • 0 Helpful votes

Redundant link via VPN

Dear Team,we have a problem in routing  between primary and secondary links.we have a two office and we are connected with intranet 2 Mb and we have configured back-up Site-Site VPN on firewall for remote office.Now the problem is when the primary is...

Resolved! OSPF - Default Route?

How does one identify what the default route is using ospf?I added it with two different commands and there is no indication what interface or network is the default route.see attachthx

Need help setting up 871 router with AT&T DSL

I've never setup a DSL connection before so I'm looking for help on things I may have missed. If you see anything in my config, let me know. I'm not sure about my NAT commands.DSL modem is 192.168.1.254Cisco 871 router is 192.168.1.250LAN DC server i...

Cisco 1811 w/12.4(24)T2 - MAC Address Filtering?

Hi,I have a couple of hosts on a remote network which are infected with a Trojan and various other malware. The hosts themselves are on a DHCP network and I would like to block access from these hosts using a MAC filter.Is this possible on 12.4(24)T2...

jpecarski by • Level 1
  • 1402 Views
  • 1 replies
  • 0 Helpful votes

Cisco 1941 Gigabit

I am interested in a Cisco 1941W or 1941 specs state it has 2 x Onboard LAN 10/100/1000. The datasheet sheet calls them WAN then LAN ports. I've seen the Cisco Router performance PDF which states this model does upto 25Mbps throughput.  Does this mea...

Load more