Hi All ,we want to use the ip source binding, ON cisco WS-C3750-48P 12.2(53)SE2 C3750-IPSERVICESK9-MNow i have find a problem about the 2 x ip address in same interface+vlanSW#config tSW(config)#ip source binding 6CF0.4948.48F9 vlan ...
I need a centralized IP address management tool to maintain and keep centralized. This can be accessed across within the organization across the globe. Can you share u r information.
Hello everybodyI need help with a NAT/PAT configuration. The scenario is very simple:- a local network with addressing 192.168.0.0/24- a router with 2 interfaces, one connected to the LAN with IP 192.168.0.1, and other connected to Internet with a pu...
Hello. Our service provider 'accidentily' changed their LAN facing interface to auto-negotiate, but our switch is hard set to 100 full duplex. We didn't notice at first, except for a couple of missed pings when the change was made. Ou Internet access...
Hi,I'm having issue with configuring cisco 877 router. 1. can't assign ip address to fa0 interface. getting error msg "ip address may not be assigned to l2 links".i did "no switchport mode access" since "no switchport" command wasn't available but st...
I have a problem with my Cisco 12000. The router was working properly at first but suddenly its services get down. I couldn't connect it even by console so I reset it but it didn't load after that and show me a number on its screen that is 00335. Wou...
hello all,in lab parctice i raplace my ios of my router to "new" 12.0 (8r) and i dont happpy with the new ios.when i try to copy tftp: idont have any opition to writh "flash"i try to serch in the net but i dont find nothing please help me tnx for the...
Dear Experts,Please help me regarding return traffic in bgp when multiple isp's in single router.we ar using multiple isp's bandwidth in single routerISP-A 45 mbISP-B 24 mbwe have our own ASN and two registerd ip pools from APNICe.g ASN : 123456 ...
haii, I am a CCNP student .While I was trying to make an ibgp network by interconnecting 3 routers seriely(R1------R2-----R3) with basic configuration.Then R1 and R2 & R2and R3 became neigbours its states shows as established.The problem is that no...
Hello all, Today I basically hooked up a telephone line for paging purposes into the Vic3-2FXS card in our Cisco 2811 router.Then from the router I ran it straight to the amplifier that we have for paging and sound. I have the sound working for rad...
I'm setting a policy map, but when I entered the fair-queue command, this message is displayed : fair-queue not allowed without bandwidth or shape featureRemote(config)#policy-map PolicyRemote(config-pmap)# class Precedence_00Remote(config-pmap-c)#fa...
Hi TeamI Have issuePlz Help MeQ1 , On My Switch STP Is already Activated Butt Still Loop ouccer In My Switch , So plz Suggest Me What i Can DoQ2 i Want Trace The MAc Address Who Sent Broadcast
I have an ASR1002 with up links to 2 different ISP's. There is a 200Mbps connection to ISP A and 65Mbps to ISP B. I am receiving full BGP routes from both ISP's. What is the best way to load balance between the asymmetric links? Thanks
Hi there,i have two vpn routers in my datacenter which is connected to MPLS cloud and around 1000 branch connected to mpls cloud by using BGP. i want to configure Qos for the ip sec traffic and make sure that this ipsec traffic is getting high priori...
Can someone help with changing the IOS used in a ASR1002 from ipbase to advipservices, I need to run BFDSo far I have copied asr1000rp1-advipservicesk9.02.06.02.122-33.XNF2.bin to the flash memory and treid simply to change the boot system statement...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 12-05-2025 03:27 AM | ||
| 11-13-2025 04:57 PM | ||
| 11-09-2025 09:51 PM | ||
| 11-06-2025 06:09 PM | ||
| 10-26-2025 02:24 AM |
| User | Count |
|---|---|
| 4 | |
| 3 | |
| 3 | |
| 2 | |
| 1 |
