Finding accurate answers to your questions and issues is always gratifying, but what if these answers are shared globally across different languages? The Cisco Community team has been working on a proof of concept (PoC) to take Accepted Solutions in...
Dear All,Please tell me how i can know the serial number of my cisco router by CLI...i used show tech command but its running so fast i m not able to read the serial number....Can anybody plz tell me a short command to get the serial number of my rou...
I've got a very simple small business setup. In looking for a replacement firewall/router combo, I'm not able to find any comparison of the 500 series router vs the ASA 5505. I know in general these do different functions, but in a small business s...
We have our Internet provider advertising network 0.0.0.0 via BGP.#sh ip bgp nei 1.2.3.1 routesBGP table version is 7, local router ID is 255.255.255.255Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RI...
show atm vpKeys: B = ATM8/0/ima12, Data CES Peak CES Avg/Min Burst MCRInterface VPI SC VCs VCs Kbps Kbps Kbps Cells Kbps CDVT Status8/0/4 11 0 0 1920 0 N/A N/A N/A N/A INACTIVE8/0/6 11 0 0 1920 0 N/A N/A N/A N/A INACTIVEB 18 0 0 30464 0 N/A N/A N/A N...
Hi all , I am having problem on understanding BGP deterministic MED . When issue the command of sh ip bgp . I can see my internal routes were assigned the value of 150 under Metric .But when , i search in the confguration , i can't see any c...
When use router SDM to create QoS policy-map, where to select "input" or "output" when apply the policy to an interface?Is serial interface' default queuing method WFQ or FIFO? Can I see that in SDM?Thanks a lot
Does anybody know what might cause a Network Monitoring Tool to report that a router interface is over 100% utilization? For instance our Solarwinds Orion Server reports that a FastEthernet connection provisioned for 50 Mbps (configured with a bandw...
I currently have sites with 2 T1 connections to an MPLS cloud. Termed in a single router by the provider. We currently are running IP CEF and max paths 2 in BGP to ensure we are load balancing. We have equal cost paths however, the load balancing ...
Hi all, Here is the topology:R9 <----> R8 <----> R7 When I attempt to ping from R7 to 239.0.0.1, I get no responces. The configurations are below, am I missing something in the configuration?R9:interface Loopback0 ip address 3.1.1.1 255.255.255.0i...
Hi, I need help on how to achieve ISP level failover for LAN based outbound and DMZ inbound traffic.Scenario (attached diagram)LAN -> Firewal1 (in HA) -> WAN Routers (1&2) (in HA using HSRP) -> ISP-01 (Using two different Last miles)LAN -> Firewal...
Hi, anyone know what the correct power cable to use for Chile is? I've been told it may be an Italy power cord. Its for a WAE-512-K9. Thanks.
Hi all,I'm trying to setup a backdoor to access to a PDU when first link down.I am sure that is possible do it with nat but i can't config it.In the attachment there are a draw of my scenario, the access throght Router A is possible without problems ...
I have a 3640 router that is effectively configured on our network as ISDN dial up for backup in case our Frame Relay network fails.My manager brought me a phone bill from our provider earlier. Last month we found that on some days, this router is d...
Hi All,Having received some great help on this forum, I have successfully installed a WIC1-ADSL card in my 2651XM router and am now thinking of getting a WIC1-SHDSL for it. The version of IOS I have on the router is: Cisco IOS Software, C2600 Softwar...
Hi all , i have one 871 router there wan port is not working ,i have done all basic troubleshot ,reset it , cable change but the port is not getting connected,can port becomes faulty or any other?Thanks
| User | Count |
|---|---|
| 16 | |
| 13 | |
| 8 | |
| 6 | |
| 6 |
.jpg "VIP Mentor"){kind=icon}
.jpg "Hall of Fame Master"){kind=icon}
