I have setup ISG + Broadhop and SCE for service control in our environment. The SCA BB reporter shows a huge amount of traffic under the package "Unknown subscriber traffic". Can somebody tell me how to find the source of this traffic?
I have setup ISG + Broadhop and SCE for service control in our environment. The SCA BB reporter shows a huge amount of traffic under the package "Unknown subscriber traffic". Can somebody tell me how to find the source of this traffic?
Hi,I have two configuration A and B. The config A is from ONT book and it should be correct setting. The config B is from me and it may not work. My questions are that:1. for config B, what happen if I config it?2. for config A, why "service-policy" ...
Wondering if 12.3 is compatible using OSPFv3?
HelloI am looking at the Cisco 38xx series router with an HWIC 1GE card connection. However I would like to know if this card gives true 1Gig speed over the ethernet or whether the 1Gig throughput will be downgraded due to the card's bus speed?I have...
how to do baselining in the router so that router can be restored to some earlier point.
This got tossed on my lap and I am rushing to try and figure out how (or if even possible) to do this. I'm a far cry from adapt at this. Basically, we have two T1's that are connected to an 1841. They are setup on the serial interfaces using PPP e...
On 7200VXR If i run the command show ip traffic | i frag, I am getting lot of the packets unfragmented. 1974197253 fragmented, 3921287034 fragments, 3170675 couldn't fragmentCan some one help me out why it is occuring.regardsshivlu
HelloI have to configure extranets.This has to be done for different routers(or subnets) belonging to 2 different vrf's.Traffic from A to B has to be allowed and denied from B to A.Could somebody advise me?Thank you Fred
Hi all,I have a problem with an 877 Router.I can't seem to get its DSL Firmware Upgraded. At present it is using:sh dsl int atm 0 | i FWInit FW: init_AMR-3.0.014_no_bist.binOperation FW: AMR-3.0.014.binFW Source: embeddedFW Version: ...
Hii ..I need some guidance on Get VPN .GetVPN is supposed to be the latest VPN solution for organistaion connected though MPLS VPN services.The Get VPN solution with MPLS VPN is straight forward but in a enterprise where the ISDN remote access is de...
Hi All,Trying to load share on two paths to a destination from a router on a serial and fast ethernet interfaces.both interfaces have minimun bandwidth of 1544Kbp/s and 25100 microsecond of total delay, hence the metric becomes 2300416.Now i want the...
We have a headquarters location where we currently use BGP to multihome to two Internet providers. We have a /16 IP network. We run an active/standby scenario, where the less preferred Internet connection gets used only if the preferred one fails. ...
Hi all. I have recently implemented a QoS policy on a L2 link which terminates on 2 1812 routers under my control. The link itself is 10 Mbit and I'm shaping the traffic on my routers to the size of the link.The problem is that the users in the remot...
I am simply trying to give EIGRP the highest priority and also priotise my multicast traffic. is the class/policy map below the best way to do it?class-map match-any Routing description EIGRP match access-group 145access-list 145 remark - Dynamic R...
Network sizing needs to be done for an SAP application. The WAN bandwidth required has to be estimated based on application parameters like response time,volume per transaction between client and server etc. Can you help me out on this, please?
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
09-28-2024 10:43 PM | ||
09-23-2024 06:56 PM | ||
08-07-2024 10:40 AM | ||
07-15-2024 05:07 AM | ||
07-13-2024 09:04 AM |
User | Count |
---|---|
14 | |
12 | |
6 | |
4 | |
3 |