HII'm trying to connect my ASA-5506X to a wireless router. ISP is Verizon FIOSISP > core switch 1 > ASA-5506-X using static ISP IP # 1 > Cisco RV130W router for Prod WIFI = no internet ISP > core switch 1 > Verizon wireless router using static ISP IP...
Forum Posts
Hi,I've just taken over administering some ASR 1006's and after adding them to our monitoring it's flagging up that the redundancy is currently configured mode SSO but operational mode is non redundant. We run two of them independently with BGP and V...
Hi Experts, We are planning for ASR 1004 RP1 upgrade activity running in ACTIVE/STANBY units ( two ASRs ), with application redundancy. My question, if I upgrade STANBY unit first and move the traffic to STANBY unit and then upgrade ACTIVE unit , st...
Hi !I have a 3945 with C3900-UNIVERSALK9-M), Version 15.4(3)M5The router was acquired used and the password recovery was disabled. It's ok for me since I don't want to recover. I just want to blank all the configurations.The problem is that, the rout...
Hi i got 2 questions about DR / Drother 1-In BMA network what's it exactly every Drother share with another Drother is it just LSA or LSDB 2- and what is it exactly DR share or forward with other Drother is it LSA or LSDB
HiI have a Ipsec between my cisco router and a cisco asa managed by other team. By any chance is there a way to configure a monitoring between the peer device for udp port 500 or the traffic inside the tunnel. With out configuring anything/ip sla res...
I was trying to create 2 networks (with N/w IDs -> 192.168.1.0 and 192.168.2.0), followed by joining these two via a router in cisco packet tracer. Now, I have assigned ips 192.168.x.i (x = 1,2 ; i = 1,2,3 i.e. 2 networks with 3 devices each). I even...
Hi guysWe have a BGP connection and we want it to be the prefered exit for two /28 specific source networks.The used equipment is a Cisco ASR9001 XR OS. I have found some commands but I am not sure this works.*****************************************...
Resolved! EIGRP Redistribution Question
Hy Guys, i have a problem with Redistribution in EIGRP, this is Topology: R1 has attached the subnet 192.168.100/24,192.168.10/24, 192.168.20/24 and 10.0.0.0/30R2 has attached the subnet 192.168.200/24,192.168.50/24, and 10.0.0.0/30R1 and R2 are in ...
Trying to find documentation from cisco that outlines what the BGP table max size is along with IPv4 and IPv6 maximum prefixes for the ASR 9902 platform.I can only find old ASR 9K documentation that is calling out 1048576 maximum prefixes for BGP tab...
Hi i got some misunderstanding about If a network (BMA) contains 5 routers and of course this network has DR/BDR and new router (A) comes in In this case if router A wants to be neighbor with other routers after he is gonna send hello message on 224....
I am trying to copy a config file from one router to another.I have the original config in a text file but when I copy it to the other router around half of the lines show up as an error and can't be read. The configuration file is fine because the o...
I recently upgraded a pair of ASR-1001-X's that were in our DC Storage for a while to repurpose them elsewhere. I brought them from running code 3.16 to 17.3. As a prerequesite, based on the upgrade matrix I also needed to upgrade the rommon as well,...
I have two circuits that I run EIGRP, the metrics perfer the bigger circuit and when it fails it uses the 2nd circuit. The issue is the gateway of last resort. I have two static ip route 0.0.0.0 0.0.0.0 X.X.X.X and have one with a metric. We h...
Resolved! Can't ping Switch from PC (using VLANS)
Hello, I'm using Cisco Packet Tracer and trying to configure VLANs and routing between them. Here are two tables, which I have used for configuring:DeviceInterfaceIP addressSubnet maskDefault gatewayR1G0/1.1192.168.1.1255.255.255.0- G0/1.10192.168.10...
